Winco HPS12000HE/F Installation And Operator'S Manual Download Page 7

7

3240

60706-236

The fuel line used to connect the supply line to the 

demand regulator must be a locally approved flexible 

fuel line.  Products used will vary in different regions 

depending on availability and local codes.  Consult 

with your local fuel supplier to ensure complete com-

pliance with ALL codes. 

1.   Remove the plastic cover plug from the demand 

regulator.

2.   Connect the flex fuel line to the demand regulator  

or the optional fuel solenoid..

DANGER: PERSONAL INJURY 

    

Do not use galvanized pipe in the fuel line runs. 

The galvanized coating will become eroded and 

flake off, causing possible obstruction or damage 

to the regulator or fuel valve. The obstruction could 

cause  an inoperative engine or an explosive fuel 

leak.

Size of pipe required for generators operating on 

natural gas/LP gas.

 

Length of Fuel Line*    Fuel Line Size

 

  less than 25 feet 

 3/4 inch black pipe

 

  25 to 100 feet 

 1 inch black pipe

 

  over 100 feet 

 not  recommended**

*allow an additional 3 feet for each standard elbow.  

Do not use ‘street ells’ (restrictive)

** Consult factory for fuel runs over 100 feet.

DANGER! - FIRE - PERSONAL INJURY -

    Be careful when sealing gas joints. Excessive 

sealing compound can be drawn into the solenoid, 

regulator or carburetor causing an engine malfunc-

tion or dangerous fuel leak

.

 

FUEL CONSUMPTION (Full Load) 

 

  Gasoline 

1.67 Gal/HR 

  LP Vapor 

2.2 Gal/HR  

200,932 BTU/HR

  Natural Gas 

200 cu ft/hr 

200,000 BTU/HR

 

 

FUEL PRESSURE

Correct fuel pressure cannot be stressed enough.  

The most common cause for inoperative systems is 

an inadequate or incorrect fuel pressure.  Power and 

performance of the engine is in direct relation to the 

correctness of the fuel system.  Shown below is a 

diagram of a typical L.P. or N.G. installation.  

Reference numbers 1 through 3 in the diagrams 

above are system parts supplied by customer.

Reference number 4 is the engine generator set.

Below is a table of the fuel pressure reading at each 

reference in the system.

Fuel Pressure Table

Single Regulator (L.P. Vapor only) 

1

3

4

UNIT OFF

TANKPSI

7-11 in

7-11 in

4-6 oz

4-6 oz

STARTING

TANK PSI

7-11 in

7-11 in

4-6 oz

4-6 oz

NO LOAD

TANK PSI 

7-11 in

7-11 in

  

4-6 oz

4-6 oz

FULL LOAD

TANK PSI

7-11 in

7-11 in

 

4-6 oz

4-6 oz

Two (2) Regulator System (L.P. Vapor only) 

1

2

3

4

UNIT OFF

TANK PSI 10-15 lbs

7-11 in

7-11 in

4-6 oz

4-6 oz 

STARTING

TANK PSI 10-15 lbs 

7-11 in

7-11 in

4-6 oz

4-6 oz

NO LOAD

TANK PSI 10-15 lbs 

7-11 in 

7-11 in

4-6 oz  

4-6 oz

FULL LOAD

TANK PSI   10-15 lbs 

7-11 in 

7-11 in

4-6 oz

4-6 oz

Summary of Contents for HPS12000HE/F





















Reviews: