Winbond Spiflash W25Q80BV Manual Download Page 77

Page: 77 / 80

W25Q80BV

Publication Release Date: Augest 01, 2012

- 77 - Revision G

10.

ORDERING INFORMATION

Notes:

The

“W” prefix is not included on the part marking.

Only the 2

letter is used for the part marking; WSON package type ZP is not used for the part marking.

Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and
Reel (shape T) or Tray (shape S), when placing orders.

For shipments with OTP feature enabled devices (P), please specify when placing orders.

(1)

25Q

80B

(2)

W = Winbond

25Q = SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O

80B = 8M-bit

= 2.7V to 3.6V

G = Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb

)

= Green Package with Status Register Power-Down & OTP enabled

(3,4)

SN = SOIC-8 150-mil SV = VSOP-8 150-mil ZP = WSON-8 6x5-mm UX = USON-8 2x3-mm
SS = SOIC-8 208-mil ST = VSOP-8 208-mil DA = PDIP-8 300-mil
TB

= 5x5-1 balls TFBGA 8x6-mm TC = 6x4 balls TFBGA 8x6-mm

I = Industrial (-40°C to +85°C)

J = Industrial Plus (-40°C to +105°C)

= Automotive Grade 3 (-40°C to +85°C) A

= Automotive Grade 2 (-40°C to +105°C)

Summary of Contents for Spiflash W25Q80BV

















































































Search results

Summary of Contents for Spiflash W25Q80BV

Reviews:

Related manuals for Spiflash W25Q80BV

Brands by name

Popular brands

Winbond Spiflash W25Q80BV, Manual

Search results

Summary of Contents for Spiflash W25Q80BV

Reviews:

Related manuals for Spiflash W25Q80BV

Brands by name

Popular brands