background image

OPERATING MANUAL FOR NATURAL REFRIGERANT 

CABINETS

IMPORTANT INFORMATION (PLEASE RETAIN THIS DOCUMENT)

This Manual covers the installation, operation and routine maintenance requirements for the following 

Williams Refrigeration products:

Williams Medi+ Range

Please read this Manual carefully before connecting the appliance.
Provided the instructions in this Operating Manual are read and implemented correctly, the optimum 

performance and reliability of your equipment should be maintained.
We assume the installer, user and service provider are appropriately trained, skilled and competent to 

properly and safely carry out the work, and will use the necessary safety equipment, and take the necessary 

precautions required of their intended work.
Improper installation, maintenance or repair may put the user at considerable risk.
Williams cabinets are available in a choice of temperature ranges.

Temperature parameters are set as follows:

High Temperature (H)

+2°C (35.6°F) / +8°C (46.4°F)

Low Temperature (L)

-18°C (0°F) / -22°C (-8°F)

General Regulations 

Declaration of Conformity:

Refrigerant Designation

Global Warming Potential

HC - R290

3

HC - R600a

3

 

Williams Refrigeration declares that all products manufactured by Williams Refrigeration comply with the 

applicable directives, and those products are therefore declared to be in conformity with the provisions of 

the above legislation.
Model No.: ...............................................................................
Serial No.: ................................................................................

WWW.WILLIAMS-REFRIGERATION.COM

Batteries Producer Registration Number: BPRN06225

Summary of Contents for Medi+ LWMP620

















Reviews: