manualshive.com logo in svg

Williams Sound Digi-Loop DL107 NET, Installation Manual

Share
Download
Williams Sound Digi-Loop DL107 NET Installation Manual Download Page 24

DL107, DL207 and DL210 2.0   Digi-Loop™ DSP Induction Loop Amplifiers

24

INPUT EFFECTS WINDOW

A463

Bass/Mid/Treble 

Pole Frequency 

all adjustable 

20-20kHz

Pole Freq Gain

all adjustable 

-INF to +12dB

Compressor

Adjustments:

Threshold 

-INF to 0dB 

Ratio 

1-10

Attack 

2-500ms

Release 

10-2500ms

Makeup Gain 

0-40dB

High Pass Filter 

toggles between 

OFF,  31, 62, 125, 

500Hz

Equalizer

Hz (Bass/Mid/Treble Pole Freq)

 - Sets the center frequency for the gain adjustment of each band. (Click then slide up/down to adjust)

dB (Bass/Mid/Treble Pole Freq Gain Adjust)

- Adjusts the amount of gain at the pole frequency.  This is adjustable from -96.0 dB to 0.0 dB in 0.5 

dB steps.

High Pass Filter

Each push of the button toggles between “OFF”, 31 Hz, 62 Hz, 125 Hz, 500 Hz, and back to OFF.  

Compressor

Threshold

 is the level of incoming signal at which compression takes effect.  The Threshold is adjustable from -96.0 dB to 0.0 dB in 0.5 dB steps.  

Ratio

 determines how much compression is applied when it takes effect.  The Ratio is adjustable from 1.0:1 (no compression) to 10.0:1 in 0.1 

steps.  

Attack

 is the speed at which compression reacts to get to the target level.  The Attack is adjustable from 2 ms to 500 ms in 2 ms steps.

Release

 controls the time that the compressor continues to work after the input signal drops beneath the threshold.  Short settings release 

the signal quickly, while long release times have the effect of sustaining the signal.  The Release is adjustable from 10 ms to 2500ms in 10ms 

steps.

Makeup Gain

 is used to bring the overall level of the sound back up, when the overall volume has been reduced by compression. This 

happens when the threshold is set low and/or the ratio has been set high. The Makeup Gain is adjustable from 0 dB to 40 dB in 0.5 db steps.

Summary of Contents for Digi-Loop DL107 NET









































Reviews:

No comments

Brands by name

Popular brands

Load more brands