WIKA DPT-20 Operating Instructions Manual Download Page 9

Page: 9 / 88

3 Product description

WIKA Operating Instructions - Differential pressure transmitter DPT-20

The pressures in two different pipelines are acquired via effective

pressure lines. The device determines the differential pressure.

Fig. 4: Measurement of the differential pressure in pipelines with DPT-20, dif

ferential pressure Δp = p

- p

With the help of the instrument, density measurement in a vessel with

changing level and homogeneous density distribution can be easily

realized. The instrument is connected to the vessel via a chemical

seal at two different measuring points.

–

Fig. 5: Density measurement with DPT-20

The instrument can also be used for interface measurement in a ves

sel with changing level. The instrument is connected to the vessel via

a chemical seal at two different measuring points.

–

Fig. 6: Interface measurement with DPT-20

Differential pressure

measurement

Density measurement

Interface measurement

Summary of Contents for DPT-20

























































































Search results

Summary of Contents for DPT-20

Reviews:

Related manuals for DPT-20

Brands by name

Popular brands

WIKA DPT-20, Operating Instructions Manual

Search results

Summary of Contents for DPT-20

Reviews:

Related manuals for DPT-20

Brands by name

Popular brands