background image

Safety 

Precautions

Page 4


In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

 

Your air conditioner should be used in such a way that it is protected from moisture. 
e.g. condensation, splashed water, etc. Do not place or store your air conditioner where it can
fall or be pulled into water or any other liquid. Unplug immediately if it occurs.
All wiring must be performed strictly in accordance with the wiring diagram located inside of
the unit.
The unit's circuit board(PCB) is designed with a fuse to provide overcurrent protection. The
specifications of the fuse are printed on the circuit board, such as: T 3.15A/250V, etc.
When the water drainage function is not in use, keep the upper and the lower drain plug firmly

plugged into 

to the unit to 

prevent

 choking.







 CAUTION

This appliance is not intended for use by persons (including child

re

n) with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning use of the appliance by a person responsible for 
their safety. Children should be supervised to ensure that they do not play with the appliance. 
Children must be supervised around the unit at all times.
If the supply cord is damaged, it must be replaced by the manufacturer,

 

its service agent or 

similarly qualified persons in order to avoid a hazard.
Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.

 

Do not remove any fixed covers. Never use this appliance if it is not working properly, or if it has 
been dropped or damaged.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar 
coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area 
and where it will not be tripped over.
Do not operate unit with a damaged cord, plug, power fuse or circuit breaker. 

R

eturn to an 

authorized service facility for examination and/or repair. 
To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

 

The appliance shall be installed in accordance with national wiring regulations.

Contact the manufacturer or authorized service technician for repair or maintenance information of 
this unit.

Contact the manufacturer or authorized i

nstaller for installation 

questions

 

of this unit.

Do not cover or obstruct the inlet or outlet grilles.
Do not use this product for functions other than those described in this instruction manual.

 

Before cleaning, turn off the power and unplug the unit.
Disconnect the power if strange sounds, smell, or smoke comes from it

 

and contact the  

manufacturer or authorized service technician for assistance.

Do not press the buttons on the control panel with anything other than your fingers.
Do not remove any fixed covers. 

Contact the manufacturer or authorized service technician if this unit 

if it is not working properly, or if it has been dropped or damaged.

Do not operate or stop the unit by inserting or pulling out the power cord plug.

Summary of Contents for ARC-148MS

























Reviews: