background image

3. The drain belt is too long or 

is broken.

4. The   drain   hose   hook   is   too 

high.

5. The   flexibility   of   compress 

spring of drain valve is too 
large. 

6.

There is any exterior in the 
drain   outlet   of   wash   tub   or 
rubber sleeve of drain valve.

4. Rehang   the   drain   hose   hook   on   the   hole 

under the pull-rod.

5. Replace the compress spring.
6. Open the cover of drain valve, take out the 

rubber sleeve of drain valve and clean it.

Water   leaks   from 
the   sides   when 
washing

1. The wash tub is broken.

2. The   seal   ring   of   speed 

reducer is broken.

3.

The   rubber   seal   ring   on   the 
speed reducer and wash tub is 
broken.

4. The overflow pipe is cracked.
5. The   rubber   sleeve   of   drain 

valve is cracked.

6. The   drain   elbow   or   drain 

joint did not connect well.

1. Replace wash tub.
2. Replace the speed reducer.
3. Replace the rubber seal ring.
4. Replace the overflow pipe.
5. Replace the rubber sleeve of drain valve.
6. Reinstall the drain elbow or drain joint.

Water leaks from 

the drain hose

1. The   outlet   of   drain   hose   or 

the drain valve is jammed.

2. The drain belt is too tight.

3.

The   flexibility   of   compress 
spring is not enough.

1. Open the cover of drain valve, take out the 

rubber sleeve of drain valve and clean it.

2. Adjust the position of the hook of drain belt 

and the pull-rod of drain valve. 

3. Replace the compress spring.

Noise occurs from 

the impeller during 

rotating

1. Exterior   material   under   the 

impeller.

2. The fasten screw of impeller 

is loose.

3. The   gear   wheel   in   speed 

reducer is damaged.

4. The   lock   screw   of   the   big 

impeller is loose.

5. Motor   fan   and   big   impeller 

are not in the same level.

6. The   surface   of   V-belt   is 

harsh.

7. Big   noise   from   the   wash 

motor.

1. Remove   the   impeller   and   take   out   the 

exterior material.

2. Tighten the fasten screw.
3. Replace the speed reducer.
4. Tighten the lock screw.
5. Adjust the motor fan until it’s in the same 

level as big impeller.

6. Replace another V-belt.
7. Replace the wash motor.

Maintenance of Twin Tub Washing Machine

4

Summary of Contents for XWT-608







Reviews: