background image

24" (61 CM) GAS WASHER/DRYER INSTALLATION INSTRUCTIONS 

WASHER/DRYER SAFETY

Table of Contents 

WASHER/DRYER SAFETY ..............................1
INSTALLATION INSTRUCTIONS ....................2

Tools and Parts ..............................................2
Alternate Parts ...............................................3
Location Requirements..................................3
Drain System..................................................4
Electrical Requirements .................................5
Gas Supply Requirements.............................5
Venting Requirements....................................6
Install Leveling Legs.......................................7

Remove Foam Packing..................................8
Connect Drain Hose.......................................8
Connect Inlet Hoses ......................................8
Secure Drain Hose.........................................9
Plan Vent System...........................................9
Install Vent System ......................................11
Level Washer/Dryer......................................11
Make Gas Connection .................................11
Connect Vent ...............................................11
Complete Installation ...................................12

You can be killed or seriously injured if you don't immediately 

 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

W10222384A

IMPORTANT SAFETY INSTRUCTIONS

When discarding or storing your old clothes dryer, remove the door.

SAVE THESE INSTRUCTIONS

Summary of Contents for LTG5243DQ - 24" Twin Washer/Dryer Laundry Center













Reviews: