18
The following notes apply to all cycle sheets where indicated in the NO TES colum n of the cycle
sheet. W hen there is a contradiction, the cycle sheet itself has priority.
WAT ER FILL NO TES
A “W ATER TEMP” of “W ASH” m eans that the v alv es are controlled by the tem perature selection
from the W ASH/RINSE TEMP key. HOT = hot water v alv e on, CO LD = cold water v alv e on,
and W ARM = both hot and cold v alv es on.
In the notes below, “pressure switch” refers to the operating pressure switch. “PS
CONTRO LLED” refers to an operation that is controlled by the pressure switch. “TIMED FILL”
refers to an operation that bypasses the operating pressure switch input to continue filling for a
lim ited tim e specified.
1. FILL is HOT, W ARM (both HOT and CO LD v alv es on), or COLD water, selectable by the
W ASH/RINSE TEMP key. Fills are through the detergent dispenser unless otherwise noted.
Fills are controlled by the operating pressure switch, unless otherwise noted. The cycle tim e
is not stalled while filling unless otherwise noted.
2. FILL is HOT, W ARM (both HOT and CO LD v alv es on), or COLD water, selectable by the
W ASH/RINSE TEMP key. Fills are through the detergent dispenser unless otherwise noted.
3. Bleach dispenser tim e is 3 seconds, using cold water only.
4. Fill for 30 seconds, shut off for 15 seconds, and fill for the rem aining 15 seconds.
5. All fills are cold from this step onwards unless otherwise noted.
6. Spray rinse -- av ailable only when warm rinse is selected. This is defined as a 25 second
warm fresh fill 5 seconds after the beginning of the step.
7. Bleach fill on for 10 seconds, followed by a water fill through the dispenser noted on the
cycle sheet. Note that this is not needed in the RINSE phase if a 2
ND
RINSE phase has done
this.
8. Fill is cold fresh water spray that bypasses the pressure switch.
CYCLE TIME NOT ES
Tim es giv en under the DURATIO N colum n are in MM:SS form at, where MM is m inutes and SS
is seconds, unless otherwise noted. Total tim e does not include tim e for VAR duration steps,
pauses, spin-to-spin nutates, or pauses between nutate-to-spins or spin-to-nutates unless
otherwise noted.
9. The cycle tim e is stalled during filling. To reflect possible cycle tim e stalls, a “+” is added to
the duration colum n for this step.
10. Soil Lev el is selected at default settings with the flexibility to m odify it by one-m inute
interv als.
11. Total Estim ate Tim e Rem aining does not count this step. Duration is denoted in
parentheses.
12. This step is only added if STAIN TREAT is activ e.
13. If selected EXTEND SPIN will add 3 m inutes to the duration of this step.
PUMP DRAIN/RECIRC NOT ES
14. CND stands for Controlled Neutral Drain. During this step, if the pressure switch is satisfied
the m achine will drop out of spin and into neutral drain until the pressure switch is reset. The
cycle tim e is STALLED in this step. To reflect possible cycle tim e stalls, a “+” is added to the
duration colum n for this step. Note that if spinning, there m ay be a short spin-to-spin nutate
if the cycle is stalled.
15. Pum p drain is turned off during final fluff and plate lev eling.
OPERATIONAL CYCLE NOTES
Summary of Contents for CALYPSO WashMotion GVW9959K-0
Page 1: ......
Page 64: ...60 NOTES ...
Page 65: ...61 SECTION FIVE TECH TIPS WIRING DIAGRAM Fig 5 1 ...
Page 68: ...CO RPO RATIO N ...
