background image

5019 318 33241

LI25BA

D

F

NL

E

GB

P

I

GR

N

DK FIN

S

PRODUCT SHEET

Control panel

Preliminary information for correct use of the hood:

Use the fastest speed setting for particularly concentrated steam and fumes. It is advisable to switch the hood on 5 minutes 
before starting to cook and leave it running for another 15 minutes at the end of cooking.

The hood is equipped with a “TOUCH SENSOR” device able to determine when the control rod is touched by the user, thus 
enabling control of lights and speeds. For this purpose, carefully read the following instructions.

Automatic switching on function

The hood is equipped with a temperature sensor that activates the motor at extraction speed (power) 1 when the ambient 
temperature in the area surrounding the hood exceeds 70°C. 

In any case, the user can still switch off or change the extraction speed (power) (refer to section “Extraction speed 
(power) control”
).

Extraction speed (power) control

Extraction speed (power) selection is cyclic according to the speed sequence 

therefore every time the TOP PART of the control rod is touched the extraction speed (power) increases by one level and 
switches off (stand-by) if the rod is touched again when the hood is on extraction speed (power) 4.

Note: Extraction speed (power) 4 remains on for 5 minutes, after which the extraction motor switches to speed 2.

By touching the rod again the extraction motor switches off (Stand-by).

The hood can also be switched off (stand-by) when the hood is on any speed, by touching the TOP PART of the control rod 
for more than 3 seconds.

The hood extraction speed (power) can be determined, since the rod is provided with a LED that changes colour according to 
the extraction speed (power) as follows:

Hood on stand-by: LED OFF

extraction speed (power) 1 - GREEN LED

extraction speed (power) 2 - ORANGE (amber) LED

extraction speed (power) 3 - RED LED

extraction speed (power) 4 - RED LED (FLASHING)

   

       

    

 

   

       

    

Top 
part

Bottom 
part

 stand-by - 1

→ 

→ 

→ 

Summary of Contents for AKR 804













Reviews: