background image

24" (61 CM) ELECTRIC WASHER/DRYER

INSTALLATION INSTRUCTIONS

WASHER/DRYER SAFETY

Table of Contents

WASHER/DRYER SAFETY ............................. 1

INSTALLATION INSTRUCTIONS ................... 2

Tools and Parts ............................................. 2
Alternate Parts............................................... 2
Location Requirements ................................ 2
Drain System................................................. 4
Electrical Requirements ................................ 4
Venting Requirements................................. 10
Install Leveling Legs.................................... 11

Remove Foam Packing .......................................11
Connect Drain Hose ............................................11
Connect Inlet Hoses ............................................12
Secure Drain Hose...............................................13
Plan Vent System ................................................13
Install Vent System ..............................................14
Level Washer/Dryer .............................................15
Connect Vent.......................................................15
Complete Installation...........................................15

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or  “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

8542748A

Summary of Contents for 8542748

















Reviews: