manualshive.com logo in svg

Whirlpool 8542748, Manual

Share
Download
Whirlpool 8542748 Manual Download Page 13

13

Secure Drain Hose

1. Move the washer/dryer to its final location and remove any 

cardboard used to move the washer/dryer.

2. Locate the plastic strap included in the parts package.

Beaded tie strap

3. Wrap the drain hose to the laundry tub leg or standpipe with 

the plastic strap (A or B below) and secure.

If the water faucets and the drain standpipe are recessed, put 
the hooked end of the drain hose in the standpipe. Tightly 
wrap the plastic strap around the water inlet hoses and the 
drain hose (C above).

Plan Vent System

Typical exhaust installations 

Typical installations vent the dryer from rear of the washer/dryer. 
Other installations are possible.

Optional exhaust installations 

This washer/dryer can be converted to exhaust out the right or left 
side. To convert the washer/dryer, use Side Exhaust Kit 
Part Number 279823. If your washer/dryer was previously 
exhausted from the right or left side, it can be converted to rear 
exhaust by using standard offset connections. To cover the hole in 
the side, one of the following plugs can be added:
692790 (white)
3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from 
the dealer from whom you purchased your washer/dryer. 

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for 
your installation. Three close-clearance installations are shown. 
Refer to the manufacturer’s instructions provided with the vent 
system.

NOTE: The following kits for close clearance alternate installations 
are available for purchase. Please reference the “Assistance or 
Service” section of your “Washer/Dryer User Instructions.”

■

Over the top Installation: 

Part Number 4396028

■

Periscope Installation (For use with dryer vent to wall vent 
mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) 
mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) 
mismatch

A. Dryer
B. Rigid metal or 

flexible metal vent

C. Clamps
D. Wall

E. Elbow

F. Clamps

G. Elbow
H. Exhaust hood

C

B

A

A

B

C

D

E

F

G

H

A. Standard rear offset exhaust installation
B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

 A. Loop system with standard elbows

B. Loop system with one offset & one standard elbow

C. Vent system with one periscope (2" [5 cm] clearance)

A

B

C

A

B

C

Summary of Contents for 8542748

















Reviews:

No comments

Brands by name

Popular brands

Load more brands