Page 6
=
Optional Equipment:
May not be present on all Lightbars
L
O
W P
O
WE
R
/ VI
O
LE
T
Latching Mode:
Level Mode -
The type of switch used is dependant on how
the operator wishes the Hi/Low feature to function:
By ap12 VDC voltage to the Violet wire for
less than 1 sec., the power supply is “latched” into low power operation.
The unit must be turned off and then back on to restore normal, Hi
power operation.
Ap12 VDC voltage to the Violet wire for more
than 1 sec. holds the power supply in low power mode until voltage is
removed.
(A Momentary Switch is Preferred)
(A Toggle Switch is Preferred)
Control Cable:
GREEN - In the factory default configuration, this wire activates Front Corner Strobes
BLUE - In factory default configuration, this wire activates Rear Corner Strobes
GREEN/WHITE TRACE - In factory default configuration, this activates Front Inboard Strobes
BLUE/WHITE TRACE - In factory default configuration, this activates Rear Inboard Strobes
GREEN/BLACK - In factory default configuration, this activates 2-Strobe TA Flash
BLUE/BLACK - In factory default configuration, this activates 4-Strobe TA Flash
VIOLET - This will initiate low power operation of all strobes See: Low Power Violet
YELLOW - In factory default configuration, this activates Passenger Alley Light*
WHITE - In factory default configuration, this activates Driver Alley Light*
WHITE/BLACK - In factory default configuration, this activates Take-Down Lights*
WHITE/BROWN - In factory default configuration, this activates Flashers*
WHITE/GREEN - In factory default configuration, this activates Right Traffic Advisor*
WHITE/ORANGE -In factory default configuration, this activates Work Lights*
WHITE/YELLOW - In factory default configuration, this activates Flashing Take-Downs*
WHITE/VIOLET - In factory default configuration, this activates Left Traffic Advisor*
NONE - This is the RFI shield drain wire and is connected to ground
WHITE/BLUE - This wire is used to activate Work Lights only if
WHITE/BLUE - lighted sign and/or cruise light options are present
WARNING:
All Customer supplied wires that connect to
the positive terminal of the battery, must be sized to supply
at least 125% of the maximum operating current and be
at the battery to carry the load. DO NOT USE
CIRCUIT BREAKERS WITH THIS PRODUCT!
FUSED
GR
EE
N
B
LUE
GR
EE
N
/WHI
T
E
TRAC
E
B
LUE/WHI
T
E
TRAC
E
GR
EE
N
/
B
L
AC
K
B
LUE/
B
L
AC
K
YELL
O
W
WHI
T
E
WHI
T
E/
B
L
AC
K
WHI
T
E/
BRO
W
N
WHI
T
E/
GR
EE
N
WHI
T
E/
ORANG
E
WHI
T
E/YELL
O
W
WHI
T
E/VI
O
LE
T
WHI
T
E/
B
LUE
Front Corner Strobes
Rear Corner Strobes
Rear Inboard Strobes
T.A. / 2 Strobe Flash
Passenger Alley Light
Driver Alley Light
Take-Down Lights
Flashers
Right Traffic Advisor
Front Inboard Strobes
T.A. / 4 Strobe Flash
Work Lights
Flashing Take-Downs
Left Traffic Advisor
Not Used or Work Lights
P
O
WE
R CAB
LE FU
S
I
NG C
H
ART
WI
R
E
CO
L
OR
FU
NCT
I
ON
3 amps
3 amps
3 amps
3 amps
3 amps
6 amps
2.5 amps
2.5 amps
5 amps
2.5 amps
6 amps
5 amps
2.5 amps
6 amps
5 amps
A
MP
RAT
I
NG
To use the chart below: After determining which function
wires you will use, add up the amp rating of each function
wire. You must then multiply this by 1.25 (see warning)
and fuse the RED power wire at this rating.
EXAMPLE:
If you are using the YELLOW, WHITE, & WHITE/
BROWN function wires, the total amp draw is
ou
7.5 amps.
Multiply this by 1.25 which comes out to 9.375 amps. Y
must fuse the RED power wire at 10 amps.
NONE -
RFI Shield Drain
BLACK -
Ground/8 AWG
RED -
+12 VDC/8 AWG
Fuse @ 40 amp for
fully loaded lightbar
Apply +12VDC to a control wire to enable that function. The
control cable connects to your control head / switch box and
is fused there. Typical fusing is 5 Amps.
NOTE: The wire functions listed in this manual are the factory default settings for a fully loaded lightbar. To find the correct
wire functions for the lightbar you ordered, refer to the switch operations sheet included with your lightbar.
R
E
D
:
+13VDC / TO DRIVER'S SIDE BRAKE LIGHT
WHI
T
E:
+13VDC / TO TAILLIGHTS
GR
EE
N
:
+13VDC / TO PASSENGER'S SIDE BRAKE LIGHT
B
L
AC
K:
(-) GROUND
4/C
CABLE
/
BRAKE-T
AIL
LIGHTS
POWER
CABLE
9M TOWMANS
EDGE
™
® for MODELS EQUIPPED with STROBE TRAFFIC ADVISOR™
CONTROL
CABLE
