Page 5
=
O
ptional Equipment:
May not be present on all Lightbars
NONE -
RFI Shield Drain
BLACK -
Ground/8 AWG
RED -
+12 VDC/8 AWG
Control Cable:
GREEN -
BLUE -
GREEN/WHITE TRACE -
BLUE/WHITE TRACE -
-
-
VIOLET -
YELLOW -
WHITE -
WHITE/BLACK -
WHITE/BROWN -
WHITE/GREEN -
WHITE/ORANGE -
WHITE/YELLOW -
WHITE/BLUE -
NONE -
WHITE/VIOLET -
the
T
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
This wire is used to activate
only if
lighted sign and/or cruise light options are present
This is the RFI shield drain wire and is connected to ground
If the WHITE/BLUE wire is used, this activates the
In the factory default configuration, this wire activates the
In factory default configuration, this wire activates the
In factory default configuration, this activates
In factory default configuration, this activates the
In factory default configuration, this activates the
In factory default configuration, this activates the
his will initiate low power operation of all strobes
Front Corner Strobes
Rear Corner Strobes
Rear Inboard Strobes
Front Outboard Strobes
Rear Outboard Strobes
Passenger Alley Light*
Driver Alley Light*
Take-Down Lights*
Flashers*
Front Inboard Strobes
(See: Low Power Violet)
Rear Flashers*
Work Lights*
Flashing Take-Downs*
Work Lights
Flashing Work Lights
GREEN/BLACK
BLUE/BLACK
WHITE/BLUE -
Fuse @ 40 amp for
fully loaded lightbar
WARNING:
All Customer supplied wires that connect to
the positive terminal of the battery, must be sized to supply
at least 125% of the maximum operating current and be
at the battery to carry the load. DO NOT USE
CIRCUIT BREAKERS WITH THIS PRODUCT!
FUSED
L
O
W P
O
WE
R
/ VI
O
LE
T
Latching Mode:
Level Mode -
The type of switch used is dependant on how
the operator wishes the Hi/Low feature to function:
By ap12 VDC voltage to the Violet wire for
less than 1 sec., the power supply is “latched” into low power operation.
The unit must be turned off and then back on to restore normal, Hi
power operation.
Ap12 VDC voltage to the Violet wire for more
than 1 sec. holds the power supply in low power mode until voltage is
removed.
(A Momentary Switch is Preferred)
(A Toggle Switch is Preferred)
GR
EE
N
B
LUE
GR
EE
N
/WHI
T
E
TRAC
E
B
LUE/WHI
T
E
TRAC
E
GR
EE
N
/
B
L
AC
K
B
LUE/
B
L
AC
K
YELL
O
W
WHI
T
E
WHI
T
E/
B
L
AC
K
WHI
T
E/
BRO
W
N
WHI
T
E/
GR
EE
N
WHI
T
E/
ORANG
E
WHI
T
E/YELL
O
W
WHI
T
E/
B
LUE
WHI
T
E/VI
O
LE
T
Front Corner Strobes
Rear Corner Strobes
Rear Inboard Strobes
Front Outboard Strobe
Rear
Passenger Alley Light
Driver Alley Light
Take-Down Lights
Flashers
Front Inboard Strobes
Outboard Strobe
Rear Flashers
Work Lights
Flashing Take-Downs
Not Used or Work Lights
Not Used or Flashing Work Lights
P
O
WE
R CAB
LE FU
S
I
NG C
H
ART
WI
R
E
CO
L
OR
FU
NCT
I
ON
3 amps
3 amps
3 amps
3 amps
3 amps
3 amps
2.5 amps
2.5 amps
5 amps
2.5 amps
2.5 amps
5 amps
2.5 amps
5 amps
2.5 amps
A
MP
RAT
I
NG
EXAMPLE:
If you are using the YELLOW, WHITE, & WHITE/
BROWN function wires, the total amp draw is
ou
7.5 amps.
Multiply this by 1.25 which comes out to 9.375 amps. Y
must fuse the RED power wire at 10 amps.
To use the chart below: After determining which function
wires you will use, add up the amp rating of each function
wire. You must then multiply this by 1.25 (see warning)
and fuse the RED power wire at this rating.
R
E
D
:
+13VDC / TO DRIVER'S SIDE BRAKE LIGHT
WHI
T
E:
+13VDC / TO TAILLIGHTS
GR
EE
N
:
+13VDC / TO PASSENGER'S SIDE BRAKE LIGHT
B
L
AC
K:
(-) GROUND
CONTROL
CABLE
9M TOWMANS™ EDGE® LIGHTBAR
Apply +12VDC to a control wire to enable that function. The
control cable connects to your control head / switch box and
is fused there. Typical fusing is 5 Amps.
NOTE: The wire functions listed in this manual are the factory default settings for a fully loaded lightbar. To find the correct
wire functions for the lightbar you ordered, refer to the switch operations sheet included with your lightbar.
4/C
CABLE
/
BRAKE-T
AIL
LIGHTS
POWER
CABLE
