background image

 

Upholstery Installation – Installation is the same for the Sandcruiser™ and the Sandpiper™ 

 

  

       

  

 

        Install seat back pad and attach buckles.                                   Install seat bottom pad and attach buckles. 

 

   

    

                

                                           Install leg pad and foot rest foam/ wrap.                                               Install foot rest hinge foam/  

 

 

 

 

 

 

 

 

 

 

 

     wraps. 

 

     

      

 

                                      Install seat belt straps to each side of the seat frame – adjust seat belt accordingly. 

 

Adjustable Components  

Foot Rest: The foot rest angle is adjustable for the user’s legs. Loosen the black locking levers and reposition 

the foot rest; retighten the locking levers. Adjust the foot rest leg pad by shortening/lengthening the straps.

 

 

Arm Rests 

The Arm Rests can be raised to a position 90 degrees from horizontal. This permits for easier transfer  

 

Seat Back Pad and Seat Bottom Pad Straps 

The seat back pad and seat bottom pad tension may be adjusted by changing the respective strap length. 

 

Summary of Contents for Sandcruiser











Reviews: