Wheaton OmniSpense ELITE Series Instruction Manual Download Page 27 | Manualshive

Page: 27 / 35

Wheaton OmniSpense ELITE Series Instruction Manual Download Page 27

WHEATON

®

OmniSpense

®

ELITE Peristaltic Pump

WHEATON | 800.225.1437 (U.S. & Canada Only) | 856.825.1100 |

www.wheaton.com

| P/N 50099067 Rev. 5/15/12 WMAN_001

27

16.3 Fuse Replacement

DANGER! BE CERTAIN THE UNIT IS DISCONNECTED FROM THE AC POWER

SOURCE.

1. Disconnect the cord-set from the AC power source.

2. Remove the fuse drawer from the unit.

3. Replace with new fuses:

108 - 120 vac unit use (2) 5x20mm, 250V, 2.0 AT fuses,

be sure the

correct cord set is used.

220-240 vac unit use (2) 5x20 mm 240V 1.0 AT fuses

, be sure the

correct cord set is used.

WEEE STATEMENT

This OmniSpense

®

ELITE peristaltic

pump is not to be discarded in typical trash outlets. This unit is to be

discarded according to WEEE guidelines established in your area. There are no reusable parts. Contact

the original distributor from which this product was purchased for proper disposal instructions.

«
...
25
26
27
28
29
...
»

Summary of Contents for OmniSpense ELITE Series




































Reviews:

No comments