Whalen Emily Full over Twin Loft Bunk Bed with Bookshelf Instruction Manual Download Page 28

 

28 

Care and Maintenance 

 

 

Use a soft, clean cloth that will not scratch the surface when dusting. 

 

Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. 

 

Using solvents of any kind on your furniture may damage the finish. 

 

Never use water to clean your furniture as it may cause damage to the finish. 

 

Always use coasters under beverage glasses and flowerpots. 

 

Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. 

 

Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create 

spotting within the furniture finish. 

 

In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a 

professional to repair your furniture. 

 

Check bolts/screws periodically and tighten them if necessary. 

 
 
 
 
 
 

Further advice about wood furniture care 

 
 

It  is  best  to  keep  your  furniture  in  a  climate  controlled  environment.  Extreme  temperature  and  humidity 
changes  can cause warping, shrinking and splitting of  wood.  It is advised to keep furniture away  from  direct 
sunlight as may damage the finish. 
 
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful 
tips will enhance your furniture as it ages. 

 

We hope you enjoy your purchase for many years.  

Thank you for your purchasing! 

Summary of Contents for Emily Full over Twin Loft Bunk Bed with Bookshelf





























Reviews: