manualshive.com logo in svg

Wexiodisk WD-4S, Installation And User Manual, Page: 15 / 52

Share
Download
Wexiodisk WD-4S Installation And User Manual Download Page 15

WD-4S

 Rev. 5.0 (201912)

Installation instructions

11

3.4

Installation

3.4.1

Preparing for the installation

Check that there is sufficient room for the machine at the installation location.

•

Check that correct connections are available for water, electricity, drainage
and possibly steam at the installation location. See TECHNICAL SPECIFI-
CATIONS.

•

Check that the overheating protection device is reset.

3.4.2

Positioning the machine

Check the following points before the machine is placed in position:

•

Check that the fuse for the machine at the site is off, blocked and that out-
going electrical circuits from the machine are non-live.

•

Remove the protective plastic on the sides which are to be stood against a
wall.

•

If holes need to be drilled in the machine, the holes must be fitted with an
edge strip or similar protection.

•

Lift the machine off the pallet by opening the door and lifting internally to-
gether with a counterstay at the back of the machine. The machine should
NOT be lifted by the handle.

•

Put the machine in position and check that it is horizontal using a spirit lev-
el. Use the legs to adjust the machine height (+ 55mm). Once the machine
has been filled with water, do another check to make sure the machine is
standing level.

Summary of Contents for WD-4S





















































Reviews:

No comments