background image

Step 1:  Attach Male Connector (7) from clamp base to Female Connector (8) 
 
Step 2:  Push connector into center hole of speaker as you place clamp base 
onto the speaker housing.  Please make sure the grommet (9) is seated properly. 
 
Step 3:  Attach two LONG Allen Bolts (4) through the clamp base and tighten 
into the housing.  Please make sure these are tight.  It is also recommend to use 
a Blue Loctite on these bolts.   
 

NOTE:

 ALLEN BOLTS TO ATTACH CLAMPS WILL BE INCLUDED IN 

THE MAIN REV 410 PACKAGING, NOT INSIDE THE CLAMP BOX.  
THERE WILL BE EXTRA BOLTS NOT USED. 
 
Step 4: Find the mounting location for the speaker and clamp and then mark the 
location on the bottom side of the pipe for the speaker wire.  
 
Step 5:  You will DRILL a hole in the bottom center of the pipe.  You should 
also de burr the hole and add a rubber or plastic grommet so the wire is not 
damaged by touching bare metal.  This can cause your speakers to short out and 
damage your speakers and amplifiers.  The speaker wire will be inserted back 
into the pipe for a clean installation.   
 
 
Step 6:  Slide the wire jacket (1) down the wire and Butt Connect the speaker 
wire coming from the tower to the speaker wire plug (5).  Red is positive and 
black is negative.   
 
Step 7: Attach Clamp Top (3) to clamp base (6) using the two Allen Bolts (2)  
There are various length bolts included.  There is 3 sizes.  Small 30 mm length 
that fits 1 ¾ to 2 ¼ inch sized pipe, medium 45 mm length that fits 2 ¼ to 2 ½ 
inch sized pipe and long 60 mm length that fits 2 ½ to 3 inch sized pipe. 
 
Step 8:  Make sure the clamp is tightened all the way so there is no movement 
 

 

 
 
 
 
 
 
 
 
 

Summary of Contents for REV 410












Reviews: