Westermo MRI-120-F4G-PSE Series User Manual Download Page 48

Page: 48 / 152

DHCP Relay

Information

Switch# show ip dhcp relay

DHCP Relay Agent ON

----------------------------------------

IP helper-address : 192.168.2.200

Re-forwarding policy: Replace

Backup and Restore

Backup Startup

Configuration

file

Switch# copy startup-config tftp:

192.168.2.33/default.conf

Writing Configuration [OK]

Note 1: To backup the latest startup configuration

file, you should save current settings to flash first.

You can refer to 4.12 to see how to save settings to

the flash.

Note 2: 192.168.2.33 is the TFTP server’s IP and

default.conf is name of the configuration file. Your

environment may use different IP addresses or

different file name. Please type target TFTP server

IP or file name in this command.

Restore

Configuration

Switch# copy tftp: 192.168.2.33/default.conf

startup-config

Show Startup

Configuration

Switch# show startup-config

Show Running

Configuration

Switch# show running-config

Proudly Distributed by Gross Automation | (877) 268-3700

www.westermosales.com | [email protected]

Summary of Contents for MRI-120-F4G-PSE Series

























































































































































Search results

Summary of Contents for MRI-120-F4G-PSE Series

Reviews:

Related manuals for MRI-120-F4G-PSE Series

Brands by name

Popular brands

Westermo MRI-120-F4G-PSE Series, User Manual

Search results

Summary of Contents for MRI-120-F4G-PSE Series

Reviews:

Related manuals for MRI-120-F4G-PSE Series

Brands by name

Popular brands