background image

6

6617-2203

Care recommendations

Follow the care recommendations below to maintain full operation of product and to 
fulfill the warranty obligations:  
• 

Do not drop, knock or shake the product. Rough handling above the specification 
may cause damage to internal circuit boards.

• 

Use a dry or slightly water-damp cloth to clean the product. Do not use harsh 
chemicals, cleaning solvents or strong detergents. 

• 

Do not paint the product. Paint can clog the product and prevent proper operation. 

If the product is used in a manner not according to specification, the protection provided 
by the equipment may be impaired.
If the product is not working properly, contact the place of purchase, nearest Westermo 
distributor office or Westermo technical support.

FCC Part 15.105 Notice:

 

 This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio 
or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
… Reorient or relocate the receiving antenna.
…  Increase the separation between the equipment and receiver.
…  Connect the equipment into an outlet on a circuit  

different from that to which the receiver is connected. 

…  Consult the dealer or an experienced radio/TV technician for help.

Agency approvals and standards compliance

Type

Approval / Compliance

EMC

EN 61000-6-2

Immunity industrial environments

EN 61000-6-4

Emission industrial environments

Declaration of Conformity

Hereby, Westermo declares that this product is in compliance with applicable EU 
directives and UK legislations. The full declaration of conformity and other detailed 
information is available at

 

www.westermo.com/support/product-support

.

Summary of Contents for MDW-45 HV

















Reviews: