background image

63

Product information from 

westerbergs

       Box 525, 301 80 Halmstad, Sweden

63

Product information from 

westerbergs

       Box 525, 301 80 Halmstad, Sweden

getting started

1. Close the outlet and fill the spa with water

Once you have closed the outlet, place the garden hose in the spa 
and fill with water until the water level is approx. 10 cm above the 
highest jet nozzle. It is very important to always maintain the correct 
water level as too low a level can cause damage to system compo-
nents. Damage due to too low a water level is not covered by the 
warranty.

N.B.

 Fill the spa tub via the filter inlet to minimise the risk of air 

pockets in the system. Keep an eye on the spa during filling. If you 
see any leaks (or flooding) anywhere, switch off the water until this 
has been rectified.

NB!

 If you have your own sunken well, for example, instead of a 

municipal water supply, it can be more difficult to achieve the correct 
chemical balance of the water.
We recommend that you contact your local water authority or the fire 
brigade, for example, to arrange to fill the spa from a tanker rather 
than your own well.

2. Switch on the power to your spa

First check that the RCD is functioning correctly and then switch on 
the power to the spa.

3. Testing

The control unit has a standard configuration from the factory. When 
power is supplied to the tub, a configuration sequence runs auto-
matically, enabling the system to check the status of the component 
electrical parts. This takes 4-5 minutes. Once this process has been 
completed, press the PUMP and AIR BLOWER buttons and run 
the jets for a few minutes to check the jet system and to clear the 
heating system of any air pockets. Once the jet system is fully op-
erational, the spa is ready for use. Check that the air control and jet 
nozzles are open. A possible problem that can arise when filling the 
tub is air pockets in the system. This can impede the performance 
of the jet streams or cause them not to work at all. This can happen 
when you fill the spa quickly. Air is left in the pipes leading to the inlet 
devices and jet nozzles and the water level rises above the openings 
in the spa before there is time to expel all the air. The air is trapped 
in the pipes, and when you start up the pump on the spa and it tries 
to draw in water there is only air in the pipes. When this happens, 
the pump cannot be configured and therefore runs without any water 
being pumped through the system. Open the hatch to the pump area 
in the panel, carefully loosen the quick release coupling at the top 
of the pump and release the air to break the airlock. Once you can 
see water coming out, retighten the quick release coupling, switch 
on the pump and, after a few seconds, it will begin to pump water 
as it should. You may need to do this several times before all the air 
is expelled. If this still does not work, you can contact Westerbergs 
customer service centre for help.

4. Protective lid

Use the spa lid when the spa is not in use, whether the tub is empty 
or full. The spa lid must always by fitted to the tub when not in use 
and locked with the lid locks provided. This is for safety reasons and 
to avoid damage that can occur in conjunction with direct exposure 
to sunlight. Damage due to too much exposure to direct sunlight is 
not covered by the warranty.

CLEANING – GENERAL INFORMATION:

Filtering the water circulation

To keep the water in the massage container clean, dirt must be 
removed mechanically and chemicals mixed in the water during 
continuous recirculation. All our tubs have a pump and filter for this 

purpose. The filter removes dirt in the water or on the water surface. 
Filtering using medium grade paper or textile filters is used for 
the tubs. Dirt that has fallen to the bottom of the tub is filtered out 
through the tub’s suction intake. 
Any particles remaining at the bottom of the tub that the system 
is unable to deal with must be removed manually, e.g. using a spa 
wand. 

1.  Do not attempt to open the electrical control box. It contains no 

 

components that can be maintained by the user.

2.  Empty, clean and refill the spa regularly using fresh water.

3.  Clean the particle filter at least once a week.

4.  All users of the spa should shower and rinse their bathing 

 

clothes before getting in. By getting people to shower and 

 

carefully wash off any soap before getting into the spa and using 

 

rinsing only when washing bathing clothes, you can avoid  

 

deposits of detergent and soap in the water of the spa.

5.  It is of utmost importance that the suction in the bottom of the 

 

tub always is clean and free from dirt that can clog the holes in 

 

the strainer. This can damage other components and reduces  

 

the tub prestandard. Faults due to clogged suction strainer are

 

not covered by warranty.

chemical balance of water

The water in the spa is clean and clear if the 
chemical components are in equilibrium.

1. pH values:

The first important indicator is the pH value of the water. The pH 

value is measured on a scale from 0 to 14, where 7 is neutral. Water 

below that level is acidic, while water above that level is alkaline. 

The human eye has a pH of approximately 7.5; water below 7.2 and 

above 7.8 will sting the bather’s eyes. Experience shows that most 

problems are caused by an excessively high pH value. An incorrect 

value reduces the effect of the disinfectant. Read more about the 

chemical balance in our separate chemicals manual. 

2. Water hardness:

The hardness of water is determined by the quantity of calcium and 

magnesium salts dissolved in the water. Hard water has high levels 

of these dissolved salts, and deposits will therefore form if nothing is 

done. Deposits can cause major damage to the walls of the tub, the 

pipes, the filter and the heating and technical equipment. Drinking 

water in Sweden is generally soft. It is not possible to reduce the 

hardness of water by adding chemicals, but it is possible to prevent 
the formation of deposits.

3. Disinfection:

Disinfectants are the chemicals that eliminate or neutralise micro-

organisms (bacteria, algae, fungi, viruses) in the water. Microorgan-

isms are small (microscopic) organisms that cannot be seen with the 

naked eye and which enter the water continuously through rain, the 

wind and the bodies of bathers. If they are not eliminated, they can 

be transmitted from one person to another through the water (and 

can cause illnesses and infections). Organic substances make the 

water in the tub cloudy. Usually, chlorine or bromine-based disinfect-
ants are used as these are hot water tubs. 

4. Foam:

Foam is a gathering of small and large bubbles and colloidal impuri-

ties on the water surface. It is caused mainly by a mixture of dirt, 

cosmetics, body care products, etc., which break off from the skin 

and are not soluble in water. This adversely affects the appearance 

and cleanliness of the water. 

5. Water analysers:

There are several types of water analyser, which are usually used to 

measure the effect of chemicals and disinfectants. Chemical (pH) – 
Disinfectant (Br, O3)

Types:

•  Box of tablets and a graduated measuring jug.

•  Litmus paper in a box.

Product information from 

westerbergs

       PO Box 525, SE-301 80 Halmstad, Sweden

ENG

ENG

Summary of Contents for Falsterbo






















































































Reviews: