Westell VersaLink 7550 User Manual Download Page 12

Page: 12 / 95

030-300629 Rev. A

February 2011

User Guide

VersaLink Wireless Gateway (Model 7550)

HARDWARE INSTALLATIONS

The following instructions explain how to install your VersaLink Gateway using 10/100 Base-T Ethernet, Wireless,

Ethernet Uplink, or USB connections. Before you begin, please read the following notes:

NOTE:

1. If your Ethernet card does not auto-negotiate, set it to half duplex. Refer to the Ethernet card manufacturer’s

instructions for installing and configuring your Ethernet card.

2. If you are using VersaLink in conjunction with an Ethernet Hub or Switch, refer to the manufacturer’s

instructions for proper installation and configuration.

3. When using a Microfilter, confirm that the DSL RJ-11 phone cable is connected to the DSL port of the DSL/HPN

non-filtered jack.

4. It is recommended that you use a surge suppressor to protect equipment attached to the power supply.

Use only

the power supply provided with your kit.

5. Depending on the installation method you are using, additional Ethernet cables may be required. Ethernet cables

and DSL filters can be purchased at your local computer hardware retailer.

6. VersaLink supports simultaneous 10/100 Base-T Ethernet and Wireless configurations. To use this installation

method, follow the instructions provided in sections 6.3.1 and 6.3.2. VersaLink does not support connection via

10/100 Base-T Ethernet and USB simultaneously.

VersaLink supports two modes for WAN access, which are configurable through VersaLink’s Web pages: (1) LAN

Ethernet port mode and (2) WAN Uplink port mode.

•

LAN Ethernet port

mode allows you to use VersaLink’s DSL port for WAN access (VersaLink’s DSL

functionality is Enabled). In this mode you should install VersaLink according to the instructions in section

6.1, Connecting VersaLink to Your DSL Network.

•

WAN Uplink port

mode allows you to use VersaLink as an Ethernet Gateway (for example, to connect to

a cable modem or to another ADSL device that provides WAN access). In

WAN Uplink port

mode,

VersaLink’s DSL functionality is Disabled. In this mode you should install VersaLink according to the

instructions in section 6.2, Connecting VersaLink to Your Network via E1/UPLINK.

Summary of Contents for VersaLink 7550































































































Search results

Summary of Contents for VersaLink 7550

Reviews:

Brands by name

Popular brands

Westell VersaLink 7550, User Manual

Search results

Summary of Contents for VersaLink 7550

Reviews:

Brands by name

Popular brands