WERKU WK400130, Original Instructions Manual

Page: 6 / 48

English
ENG
ORIGINAL INSTRUCTIONS
6
ELECTRONIC OVERLOAD PROTECTION.
In case that the mixer is extremely forced, an elec-
tronic protection protects the motor from damage.
In this case, the motor stops and restarts only after
the feeding pressure is reduced.
ELECTRONIC OVERHEATING PROTECTION.
To protect the motor from overheating at extreme
permanent load, it is switched off by the electronic
protection system when a critical temperature is re-
ached. After a cooling-down period of approxima-
tely 3 and 5 minutes, the mixer is again ready for
use and can be fully loaded.
MIX PROCESS.
The election of the mixer mechanism (stirrer) is de-
cisive for the result of the mixture. Two factors are
determining at the time of making this decision: the
volume to be mixed defines the diameter of the mi -
xer mechanism and the type of material defines the
geometry of the mixer mechanism.
MIXING WAY.
The material is lead upwards from the bottom of the
container, happening through the center of the mix
mechanism, returning to flow laterally downwards.
Suitable for dry mixtures like mortar, paste sticky,
substances that contain sand and gravel. The mixer
mechanism crosses the mixture materials easily.
ERGONOMICS.
Less muscular force is required and the engine
power is more used. A body relaxed position and
the handling of the grip make easier the working
process. The mixer has been designed until the last
detail considering ergonomic aspects. Ergonomic
design handle in accordance with the position of the
hand; in order to work in a relaxed way and without
unnecessary efforts.
MAINTENANCE.
The mixer has been designed for a long working life
with minimum maintenance. Optimum use depends
on correct care of the mixer and regular cleaning.
To prevent accidents, always unplug the mixer from
the power source before cleaning or performing any
maintenance. The mixer may be cleaned effectively
using compressed air after each use. If compressed
air is not available, use a brush to remove dust from
the mixer. Motor ventilation vents and switch levers
must be dept clean and free of foreign matter. Do
not attempt to clean by inserting pointed objects
through openings. Cetain cleaning agents and sol-
vents damage plastic parts, among them are ga-
soline, carbon tetrachloride, chlorinated cleaning
solvents, ammonia and household cleaners contai-
ning ammonia. Do not use any of these to clean
the mixer. Should excessive sparking occur, have a
Werku
®
official repair service exam and/or replace
the carbon brushes.
ENVIRONMENT PROTECTION.
The materials and components that have been
used to manufacture this product can be re-used
and recycled. Werku
®
is adhered to an Integrated
Management System that is in charge of the co-
rrect elimination of the residues of this product. Do
not eliminate this product with domestic residues.
Werku
®
offers to its clients a free collection service
of these residues through any of its sale points, or
in the collection points established by the Integra-
ted Management System or in the recycling point
of your locality.
WARRANTY AND TECHNICAL SERVICE.
Werku
®
offers a warranty that covers the repair of
all defects found due to faults in the materials or
manufacture. For this cover to be effective it is ne -
cessary for these defects to appear within the vali-
dity period. The consumer is entitled to free repair
of all defects (shipping costs, labour costs and ma-
terials included), either via the repair or by replace-
ment (if necessary, with a later model). In any case,
Werku
®
will not accept replacements if these repre-
sent a disproportionate cost compared to the cost
of repair. This warranty does not affect consumer’s
rights established by European or national laws.
The validity period of this warranty is 3 years. The
validity period starts on the date of purchase by the
first consumer. This date is shown on the invoice
or receipt of purchase. Any claims arising from this
warranty must be presented to the Werku
®
distri-
butor or the Werku
®
Technical Assistance Service.
To do so you must present this warranty correctly
completed and stamped by the distributor, together
with the sales invoice or receipt. To require any in-
formation in relation to this warranty, the buyer and/
or distributor may contact the Technical Assistance
Service by telephone on +34 981 648 119, or by
e-mail at info@werku.com. This warranty does not
cover defects caused by parts that have worn out
from use other types of natural wear, defects cau-
sed by failure to observe the instructions for use
and operation, or for applications other than those