![background image](http://html.mh-extra.com/html/wen/71707/71707_manual_956564016.webp)
OPERATION
MAKING A CROSS CUT (Fig. 14)
Cross cuts are straight cuts, where the material is fed into the cutting
wheel cut at a 90° angle. The width of the tile should be shorter than
18 inches.
1. Using a marker or grease pencil, mark the line of cut on the tile.
2. Position the rip guide at the desired cutting width from the cut-
ting wheel and securely lock the lever.
3. Place the tile on the table and seat it firmly against the rip guide.
Make sure the material is clear of the cutting wheel before turning
on the saw.
4. Turn the power switch to the ON position. Let the cutting wheel
12
material can interfere with tool function.
TO MAKE A CROSS CUT
Cross cuts are straight 90° cuts. The material is fed into the cut at a 90° angle to the wheel.
1.
Using a marker or grease pencil, mark the area to be
cut on material.
2.
Remove the miter guide.
3.
Position the rip guide the desired distance from the
wheel for the cut and securely lock the lever.
4.
Place the material on the table and firmly against the
rip guide.
5.
Make sure the material is clear of the cutting wheel
before turning on the saw.
6.
Turn the on/off switch to the
ON
position.
7.
Let the cutting wheel build up to full speed and wait
for the wheel to get wet before moving the material into the wheel.
8.
Hold the material firmly against the rip guide and feed the material into the cutting wheel.
9.
When the cut is made, turn the saw
OFF
. Wait for the cutting wheel to come to a complete stop before
removing any part of the material.
TO MAKE A 45° DIAGONAL CUT
45° Diagonal cuts are also referred to as “long point-to-long point cuts”.
1.
Using a marker or grease pencil, mark the area to be
cut on material.
2.
Install the miter guide.
3.
Adjust miter guide to 45° using angle scale and
tighten securely with lock knob.
4.
Position the rip guide the desired distance from the
wheel for the cut and securely lock the lever.
5.
Place the material on the table and firmly against the
rip guide.
6.
Make sure the material is clear of the cutting wheel
before turning on the saw.
7.
Turn the on/off switch to the
ON
position.
8.
Let the cutting wheel build up to full speed and wait for the wheel to get wet before moving the material
into the wheel.
9.
Hold the material firmly against the miter guide and slide miter guide along rip guide. Feed the material
into the cutting wheel.
10.
When the cut is made, turn the saw
OFF
. Wait for the cutting wheel to come to a complete stop before
removing any part of the material.
12
material can interfere with tool function.
TO MAKE A CROSS CUT
Cross cuts are straight 90° cuts. The material is fed into the cut at a 90° angle to the wheel.
1.
Using a marker or grease pencil, mark the area to be
cut on material.
2.
Remove the miter guide.
3.
Position the rip guide the desired distance from the
wheel for the cut and securely lock the lever.
4.
Place the material on the table and firmly against the
rip guide.
5.
Make sure the material is clear of the cutting wheel
before turning on the saw.
6.
Turn the on/off switch to the
ON
position.
7.
Let the cutting wheel build up to full speed and wait
for the wheel to get wet before moving the material into the wheel.
8.
Hold the material firmly against the rip guide and feed the material into the cutting wheel.
9.
When the cut is made, turn the saw
OFF
. Wait for the cutting wheel to come to a complete stop before
removing any part of the material.
TO MAKE A 45° DIAGONAL CUT
45° Diagonal cuts are also referred to as “long point-to-long point cuts”.
1.
Using a marker or grease pencil, mark the area to be
cut on material.
2.
Install the miter guide.
3.
Adjust miter guide to 45° using angle scale and
tighten securely with lock knob.
4.
Position the rip guide the desired distance from the
wheel for the cut and securely lock the lever.
5.
Place the material on the table and firmly against the
rip guide.
6.
Make sure the material is clear of the cutting wheel
before turning on the saw.
7.
Turn the on/off switch to the
ON
position.
8.
Let the cutting wheel build up to full speed and wait for the wheel to get wet before moving the material
into the wheel.
9.
Hold the material firmly against the miter guide and slide miter guide along rip guide. Feed the material
into the cutting wheel.
10.
When the cut is made, turn the saw
OFF
. Wait for the cutting wheel to come to a complete stop before
removing any part of the material.
Fig. 14
Fig. 15
build up to full speed and wait for the wheel to get wet feeding the material into the cutting wheel.
5. Hold the material firmly against the rip guide and feed the material into the cutting wheel in a smooth motion
(Fig. 14). Hold down on the edges of the tile to prevent the tile from lifting during the cut.
6. When the cut is completed, turn the saw OFF. Wait for the cutting wheel to come to a complete stop before
removing any part of the tile.
MAKING A MITER CUT (Fig. 15)
The tile can be cut at a miter angle from 0 to 45 degrees, by setting
the miter guide. The width of the tile should be shorter than 12
inches.
1. Using a marker or grease pencil, mark the line of cut on the tile.
2. Install the miter guide on top of the rip guide. Adjust the miter
guide to the desired miter angle using angle scale and securely
tighten the lock knob.
3. Position the rip guide the desired distance from the cutting
wheel and securely lock the rip guide lever.
4. Place the tile on the table and with the corner held firmly inside
the miter guide. Make sure the material is clear of the cutting wheel before turning on the saw.
5. Turn the power switch to the ON position. Let the cutting wheel build up to full speed and wait for the wheel to
get wet feeding the material into the cutting wheel.
6. Hold the tile firmly against the miter guide and rip guide, and feed the material into the cutting wheel in a
smooth motion (Fig. 15). Hold down on the edges of the tile to prevent the tile from lifting during the cut.
7. When the cut is finished, turn the saw OFF. Wait for the cutting wheel to come to a complete stop before
removing any part of the material.
16
Summary of Contents for 71707
Page 22: ...EXPLODED VIEW PARTS LIST 22 ...
Page 24: ...THANKS FOR REMEMBERING ...