manualshive.com logo in svg

Wen 65812, Manual

Share
Download
Wen 65812 Manual Download Page 9

248mm

25mm

60mm

200mm

250mm

328mm

FRONT

BACK

Mouting Hole

2xø10mm

Rubber Feet Ho

le

4xM6

WARNING: 

To prevent serious injury from accidental operation, make sure the power cord is discon-

nected from the power source and the tool is turned OFF before assembly or making any adjustments.

ASSEMBLY & ADJUSTMENTS

SECURING SANDER TO A WORKBENCH

For safe operation, the machine must be secured onto a flat, secure workbench or stand. Refer to the base dimen-
tsions shown in Fig. 2. For temporary mounting, attach a large C-Clamp to each side of the sander and the work-
bench. For permanent mounting,  follow the instructions below:
 

1. Place the sander on a stable workbench.

2. A mounting hole is located on each leg towards the rear of the 
sander body (Fig. 1). Insert a pencil through the two mounting 
holes and mark the hole locations on the workbench.

3. Remove sander. Drill two 3/8" holes through the workbench.

4. Align the sander base over the mounting holes and secure it 
using two 5/16" screws and washers, locking washers and hex nuts 
(mounting hardware not included).

Mounting
   holes

Fig. 1 

Fig. 2 

NOTE: 

Your sander is compatible with the WEN 6588 Multipurpose Planer Stand, available at wenproducts.

com. Forget measuring and drilling holes on your workbench, simply mount your machine onto the mobile 
stand with pre-drilled holes, and transport your machine around the workshop with ease.

9

Summary of Contents for 65812





















Reviews:

No comments

Brands by name

Popular brands

Load more brands