manualshive.com logo in svg

Wen 65812, Manual

Share
Download
Wen 65812 Manual Download Page 6

SPECIFIC RULES FOR SANDERS

WARNING:

 Do not let comfort or familiarity with the product replace strict adherence to product 

safety rules. Failure to follow the safety instructions may result in serious personal injury. 

1. TOOL PURPOSE. Your disc sander is intended for sanding natural, solid woods and composite materials. 
Operations for which the tool was not designed, including modification of the machine, may cause machine dam-
age or personal injury, and invalidate the warranty.

2. WORK ENVIRONMENT. Do not operate the tool in wet or damp conditions; doing so significantly increases 
the risk of electrical shock. Do not operate the tool in the presence of flammable liquids or gases; sparks gener-
ated by the tool could ignite these flammable materials. Keep the work area clean.

3. SECURING THE TOOL. For operation safety, mount the machine to a flat and secure work surface or stand.

4. PERSONAL SAFETY. Tie back long hair. Do not wear loose clothing or jewelry as they might get drawn in by 
the tool. Always wear ANSI Z87.1-approved glasses with side shields, hearing protection and a dust mask when 

using the sander. 

5. DO NOT wear gloves while operating this machine.

6. DUST COLLECTION. Use of sanders can produce harmful particles while sanding certain types of woods. 
Be sure to wear a dust mask and connect the sander to an adequate dust collection system.

7. TOOL  & ACCESSORIES INSPECTION. Before operation, check the tool and accessories for any damage 
or missing parts. Do not use the tool if any part is missing or damaged. Make sure all adjustments are correct and 
all connections are tight. Keep all guards in place. 

8. PREVENT ACCIDENTAL STARTING. Make sure the power switch is in the OFF position prior to plugging 
in the machine. Always make sure the power switch is in the OFF position and the machine is unplugged when 
doing any cleaning, assembly, setup operations, or when not in use.

9. KEEPS HANDS AWAY. Keep your hands and all other body parts away from the rotating sanding disc. Do 
not attempt to stop the sanding disc with your hand. Keep hands at a safety distance from the disc while sanding.

10. SANDING DISC. Use only 12-inch PSA adhesive-backed sanding discs.. The use of any accessories or at-
tachments not recommended may cause injury to you and damage your machine. Replace worn, folded or torn 
discs. Replacement sanding discs can be purchased from wenproducts.com by searching 65812SD.

11. TABLE DISTANCE. Maintain a 1/16 inch clearance between the sanding disc and table to avoid trapping the 
workpiece or fingers. 

12. SUPPORTING THE WORKPIECE. Always support the workpiece firmly on the worktable. Use the miter 
gauge or suitable jigs when sanding small workpieces. 

13. TURNING OFF THE TOOL. After operation, switch off and unplug the power cord. Allow the tool to stop 
completely (takes about 4.5 minutes) before cleaning, changing accessories or making adjustments on the tool.

These safety instructions can’t possibly warn of  every scenario that may arise with this tool, 

so always make sure to stay alert and use common sense during operation.

6

Summary of Contents for 65812





















Reviews:

No comments

Brands by name

Popular brands

Load more brands