Wen 6559 Manual Download Page 3 | Manualshive

Page: 3 / 24

Wen 6559 Manual Download Page 3

For replacement parts visit

WENPRODUCTS.COM

XXX

INTRODUCTION

Thanks for purchasing the WEN Jointer. We know you are excited to put your tool to work, but

first, please take a moment to read through the manual. Safe operation of this tool requires that

you read and understand this operator’s manual and all the labels affixed to the tool. This manual

provides information regarding potential safety concerns, as well as helpful assembly and operating

instructions for your tool.

NOTE:

The following safety information is not meant to cover all possible conditions and situations

that may occur. WEN reserves the right to change this product and specifications at any time without
prior notice.

Keep this manual available to all users during the entire life of the tool and review it frequently

to maximize safety for both yourself and others.

SAFETY ALERT SYMBOL:

Indicates danger, warning, or caution. The safety symbols and

the explanations with them deserve your careful attention and understanding. Always follow the
safety precautions to reduce the risk of fire, electric shock and personal injury. However, please
note that these instructions and warnings are not substitutes for proper accident prevention
measures.

3

«
1
2
3
4
5
...
»

Summary of Contents for 6559

























Reviews:

No comments