manualshive.com logo in svg

Wen 6559, Manual, Page: 2 / 24

Share
Download
Wen 6559 Manual Download Page 2

TABLE OF CONTENTS

Specifications .................................................................................. 2
Introduction .................................................................................... 3
General Safety Rules ....................................................................... 4
Specific Safety Rules for the Jointer ................................................ 6
Electrical Information ...................................................................... 8
Know Your Jointer ........................................................................... 9
Assembly & Adjustments .............................................................. 10
Operation ...................................................................................... 13
Maintenance .................................................................................. 17
Troubleshooting Guide .................................................................. 19
Exploded View & Parts List ........................................................... 20
Warranty Statement ....................................................................... 23

SPECIFICATIONS

Model Number

6559

Motor

120V, 60 Hz, 10A

Cutterhead Rotation Speed

10,000 RPM

Cuts Per Minute

20,000 CPM

Max Cutting Width

6-1/8 in.

Max Cutting Depth

1/8 in.

Recommended Cutting Depth 1/32 in.
Number of Blades

2

Table Size

28-1/2 in. x 6-1/4 in.

Fence Size

20-3/4 in. x 4-1/4 in.

Dust Port Diameter

60 mm (fits 2-1/2 in. dust hose)

Fence Bevel

45°

Product Dimensions

28-1/2 in. x 20 in. x 14 in.

Weight

29.3 lbs

Jointer parts and accessories can be purchased from 

wenproducts.com

.

2

Summary of Contents for 6559

























Reviews:

No comments