background image

5. Connect the nailer to the air supply. Load the magazine and test fire a nail into a scrap piece of wood to con-
firm the nailer is working properly again. 

WARNING: 

If nails continue to jam, stop using the nailer. Contact our customer service department 

at 800-232-1195 (M-F 8-5 CST).

1. Disconnect the nailer from the air supply.

2. Pull the feeder shoe all the way to the back of the magazine 
until  it  latches.  Slide  fasteners  to  the  back  and  remove  all  re-
maining fasteners from the magazine.

3. Use a pair of needle nose pliers or a flat head screwdriver to 
remove the bent fastener from the back opening of the nose-
piece (Fig. 11 - 1). If the fastener cannot be removed directly, 
refer to the next step to remove the magazine. 

CLEARING JAMMED FASTENERS (Fig. 11 & 12) 

WARNING:

 Disconnect air line from the tool and remove all fasteners before removing jammed 

nails to avoid personal injury. Keep the tool pointed away from yourself and others.

1

2

Fig. 12

OPERATION

Fig. 11

1

4. Remove the angle adjustment wheel and five hex screws (Fig. 12 - 1 & Fig. 12 - 2). Slide the magazine off the 
nosepiece. Keep note of the orientation of each part so that you can reassemble the magazine. Remove the bent 
fastener. Reattach the magazine and re-install the screws.

15

Summary of Contents for 61731





















Reviews: