background image

M01

1D.01 2M-Z17558 Owners Manual for Built-In Round T’Stat W

armers

13

CLEANING INSTRUCTIONS

WEEKLY CLEANING INSTRUCTIONS 

PREPARATIONS:  

 Remove any insets, pans and/or adapter tops.

 

Drain or remove water from well if used for wet  

operation. 

FREQUENCY:      

Weekly, or whenever lime or scale is seen               

accumulating on the sides of the warmer pans.

TOOLS:         

Commercial Delime Cleaner

 

Plastic Scouring Pad 

 

Clean Cloth or Sponge 

1.  Add water to pans until water is at normal operating level  

(1” - 1 1/2” deep) or covers accumulated scale.

2.   Heat water to maximum temperature (190ºF or higher).

3.   Pour contents of one package of commercial delime cleaner   

into each warmer pan.  Stir to dissolve cleaner. Turn heat     

control OFF.  Cover pans.

4.   Allow solution to soak at least one hour, or overnight for heavy  

scale buildup.

5.   Drain hot water from pans.  Scrub with a plastic scouring pad.   

Rinse thoroughly with hot water, then dry.

6.   Refill pans with hot tap water and resume operation.

7.   Heavy scale buildup may require additional treatments.

CAUTION:

CHEMICAL BURN 

HAZARD

Delimng chemicals may be 

caustic.  Wear appropriate    

personal protective equipment.

Follow cleaner manufacturer’s 

instructions for safest use.

Summary of Contents for SS-10T

























Reviews: