background image

M01

1D.01 2M-Z17558 Owners Manual for Built-In Round T’Stat W

armers

11

MAINTENANCE INSTRUCTIONS

CARE OF STAINLESS STEEL

Stainless steel is a marvelous material:  strong, lustrous and low maintenance. With 

a minimum of care, it will normally retain its beauty and durability for the life of  the     

equipment.  In some applications, however, special care is required in order to maintain 

stainless steel’s special properties.

External components, such as cabinets and control panels, are finished with a grain  

pattern. This pleasing finish is best maintained by cleaning with a non-abrasive      

cleanser applied with a soft cloth.  Rub only in the direction of the grain.  In the absence 

of visible grain, rub only along the longest axis of the appliance.

Restore stainless steel’s luster by applying a polish specifically made for stainless steel. 

Spray on, wipe off with a soft cloth, rubbing in the direction of the grain.

Never use metal implements, wire brushes, abrasive scratch pads or steel 

wool to clean stainless steel.

Warmer pans, insets and other vessels are subject to a harsher environment.  Wells 

Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer 

pans.  Even the highest quality stainless steel, however, is mostly iron, and will rust, pit 

and corrode under the following conditions:

 

Poor Water Quality:  

Hard water (water with a high content of dissolved minerals)

will leave mineral deposits when allowed to dry.  Calcium (lime) can buildup on

heated surfaces, even under water.  If left unattended, hard water spots and lime

buildup can lead to rusting, corrosion and pitting.

 

Contact with Chlorides:  

Chlorides (specific compounds of chlorine) are found in

food, table salt and many cleansers.  Chlorides can attack the surface of stainless

steel, resulting in corrosion and pitting.

Keep your stainless steel warmers clean and free from calcium buildup.

Use alkaline, alkaline chlorinated or non-chloride cleanser.  

Use citric acid-based cleaners to remove calcium deposits.

For additional information, please read the NAFEM Stainless Steel Equipment and 

Cleaning Guide.  Contact NAFEM at :

North American Association of Food Equipment Manufacturers

401 N. Michigan Avenue

Chicago, Illinois  60611-4267

(312) 644-6610

Summary of Contents for SS-10T

























Reviews: