background image

047 p/n 307538  OpM Free-Standing Drawer W

armer w/ Solid State Control

This appliance is intended for use in commercial establishments 

only.
This appliance is intended to prepare food for human consumption.  

No other use is recommended or authorized by the manufacturer or its 

agents.
Operators of this appliance must be familiar with the appliance use, 

limitations and associated restrictions.  Operating instructions must be 

read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation.  Read and 

follow all included cleaning instructions and schedules to ensure the 

safety of the food product.
Disconnect this appliance from electrical power before performing any 

maintenance or servicing.
DO NOT submerge this appliance in water.  This appliance is not jet 

stream approved.  Do not direct water jet or steam jet at this appliance, 

or at any control panel or wiring.  Do not splash or pour water on, in or 

over any controls,  control panel or wiring.   Do not wash floor around 

this appliance with water or steam jet.
Exposed surfaces of this appliance can be hot to the touch and may 

cause burns.
Heating element will be very hot when in use.  Contact may cause    

serious burns.
The technical content of this manual, including any wiring diagrams,

schematics, parts breakdown illustrations and/or adjustment

procedures, is intended for use by qualified technical personnel.

Any procedure which requires the use of tools must be performed by a 

qualified technician.

This manual is considered to be a permanent part of the appliance.  

This manual and all supplied instructions, diagrams, schematics, parts 

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.
This appliance is made in the USA.  Unless otherwise noted, this

appliance has American sizes on all hardware.

PRECAUTIONS AND GENERAL INFORMATION

3

STD 4

E6070

This appliance conforms to NSF Standard 4 for sanitation only if

installed in accordance with the supplied 

Installation Instructions 

and 

maintained according to the instructions in this manual.
This appliance is NSF approved for potentially hazardous foods.

This appliance is      and       Listed under UL File E6070 for 120V, 208V 

and 240V.

E6070

AGENCY LISTING INFORMATION

WARNING:

SHOCK HAZARD

All servicing requiring

access to non-insulated    

electrical components must 

be performed by a factory 

authorized technician.

DO NOT open any access 

panel which requires the use 

of tools.  Failure to

follow this warning can

result in severe electrical 

shock.

CAUTION:

RISK OF

DAMAGE

DO NOT connect or energize 

this appliance until all        

installation instructions are 

read and followed.  Damage 

to the appliance will result if 

these instructions are not

followed.

CAUTION:

HOT SURFACE

Exposed surfaces can be hot 

to the touch and may cause 

burns.

Summary of Contents for RWN-1 thru RWN-3 Narrow

















Reviews: