background image

UNPACKING & INSPECTION

Carefully remove the appliance from the carton.  Remove all 

protective plastic film, packing materials and accessories from the

Appliance before connecting electrical power or otherwise performing 

any installation procedure.
Carefully read all instructions in this manual and the 

Installation

Instruction Sheet

 packed with the appliance before starting any

installation.
Read and understand all labels and diagrams attached to the

appliance.
Carefully account for all components and accessories before

discarding packing materials.  Store all accessories in a convenient 

place for later use.

 COMPONENTS
  1 - 3 ea.  DRAWERS (qty. depends on model)

  1 - 3 ea. HUMITROL RACKS (if ordered with unit)

SETUP

Setup the appliance only on a firm, level, non-combustible surface.  

Verify local codes for requirements.  Concrete, tile, terrazzo or metal 

surfaces are recommended.  Metal over  combustible material may not 

meet code for non-combustible surfaces.

 

Install adjustable legs or optional casters, one on each corner of the 

appliance, in the holes provided.

Verify that the unit sits firmly 

ON ALL FOUR LEGS.  With a spirit level, 

check that the appliance is level front-to-back and side-to-side.  With 

the adjustable legs, adjust as required to level the appliance.  All four 

legs must be adjusted to firmly contact the floor in order to prevent    

tipping. 
If drawers were removed during installation, install drawer(s) in unit: 

a.  Check the roller catch inside the cabinet.  The spring-loaded  

roller arm must be extended.

b.  With the front of the drawer assembly tipped downward,         

engage the roller on the drawer with the cabinet drawer slide.

c.  Raise the drawer to the horizontal position until the drawer-  

mounted slide engages the dual roller assembly on the cabinet.

d.  Slide the drawer in until the catch engages.  The drawer should  

remain tightly closed.

e.  Slide the drawer out.  The drawer stop should prevent the   

drawer from coming all of the way out.

f.  Install drawer insert pans.

Avoid storing flammable or combustible materials in, on or near the   

appliance.

INSTALLATION

4

047 p/n 307538  OpM Free-Standing Drawer W

armer w/ Solid State Control

NOTE:

  DO NOT discard

the carton or other packing

materials until you have

inspected the appliance for

hidden damage and tested it 

for proper operation.

Refer to 

SHIPPING DAMAGE 

CLAIM PROCEDURE 

on the 

inside front cover of this

manual.

WARNING:

RISK OF 

INJURY

Installation procedures must 

be performed by a qualified 

technician with full knowledge 

of all applicable electrical and 

plumbing codes.  Failure can 

result in personal injury and 

property damage.

IL2926

MOUNTS INTO

THREADED

HOLES IN 

WARMER

FRAME

TURN BOTTOM

PORTION TO

ADJUST

Summary of Contents for RWN-1 thru RWN-3 Narrow

















Reviews: