Wells RCP-100 Operation Manual Download Page 7 | Manualshive

Page: 7 / 16

background image

5

ELECTRICAL INSTALLATION

1.   Refer to the nameplate.  Verify the electrical service power.
      Voltage and phase must match the nameplate specifications.
      Wiring the unit to the wrong voltage can severely damage the unit
      or cause noticeably decreased performance.

2.   Available electrical service amperage must meet or exceed the
      specifications listed on the specification sheet provided with the
      unit.
      a.     Units are equipped with a three-prong (grounding) plug for your
               protection against electric shock.  This must be plugged into a
               properly grounded matching receptacle.
      b.     RCP-100 thru -600 and RCP-7100 thru -7400 are equipped
               with a NEMA 5-15P plug and require a matching NEMA 5-15R
               receptacle.

      c.     RCP-7500 and -7600 are equipped with a NEMA 5-20P plug
               and require a matching NEMA 5-20R receptacle.

PLUMBING INSTALLATION

1.

Plumb connections must be made in compliance with all Federal,

State and Local Plumbing Codes and Ordinances.

IMPORTANT:

All drain plumbing installations must be performed

by a qualified plumber.

2.   Install 1" drain valve (provided by others) on unit drain. Plumb to
      an appropriate waste as required by local plumbing and sanitation
      ordinances.

INSTALLATION (continued)

WARNING:

Electric
Shock hazard

All servicing requiring
access to non-insulated
electrical components must
be performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools.  Failure to
follow this warning can
result in severe electrical
shock.

CAUTION:

Risk of
Damage

DO NOT connect or energize
this appliance until all
installation instructions are
read and followed.  Damage
to the appliance will result if
these instructions are not
followed.

CAUTION:

Electrical Shock
Hazard

Cord -connected units are
equipped with a three-prong
plug for your protection
against electric shock. Never
cut the large round prong
from the plug, or twist a blade
to fit an existing receptacle.

IMPORTANT:

Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.

«
...
5
6
7
8
9
...
»

Summary of Contents for RCP-100

















Reviews:

No comments

Related manuals for RCP-100

Brand: Randell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands