background image

 

This appliance should never be left unattended when plugged in. 

 

Close  supervision  is  necessary  when  this  appliance  is  used  by,  on,  or  near  children  of 
invalids. 

 

Never operate this appliance if it has a damaged cord or plug, if it is not working properly. 

 

Keep the cord away from heated surfaces. 

 

Do not pull, twist, or wrap line cord around appliance. 

 

Never drop or insert any object into any opening on this appliance. 

 

Before use, make certain blades are aligned properly. 

 

Do not place appliance on any surface while it is operating. 

 

Do not use this appliance with a damaged or broken comb or with teeth missing from the 
blades as injury may occur. 

 

INSTRUCTIONS FOR HAIR CUTTING 

Before starting the hair cut: 
1. Inspect the clipper, making sure that it is free of oil between the cutting blade teeth and 
turn the unit on to distribute the oil and to make sure it is running smoothly. Wipe off any 
excess oil. This should be done after each use. While using the unit, untwist the cord from 
time to time to avoid tangling. 
2. Seat the person so their head is  approximately at your eye level. This allows ease of 
visibility while cutting and a relaxed control of the unit. 
3. Before cutting always first comb the hair so it is tangle free and as it is naturally worn. 
4. Place a towel around the neck and shoulders of the person having the haircut. 

 
 

REMINDERS 

 

Cut the hair in a relaxed and slow manner. Use short strokes only to work gradually over 
the entire head. 

 

Always take off a little hair at a time, you can always trim off additional hair later. 

 

As you work, comb the hair frequently back into the style to which you are cutting. 

 

When cutting with this hair clipper it is better to leave the hair dry, not wet. With the hair 
dry, it is much easier to control the amount of hair being cut. 

 
 

 
BEGINNING THE HAIRCUT 

Cutting hair requires practice so it is always better to leave the hair longer for the first few haircuts 
until you become used to the length from each attachment comb. 
 
 
 

 
ATTACHMENT COMB (see main diagram) 

 

Attachment Comb #1 leaves 3 mm (1/8 inch) hair length. 

 

Attachment Comb #2 leaves 6 mm (1/4 inch) hair length. 

 

Attachment Comb #3 leaves 9 mm (3/8 inch) hair length. 

Summary of Contents for CLIPP-HAIR-RAVEN-WL










Reviews: