WELDMAN
POWER PULSE DC TIG 200 HF / LIFT
6
After setting the operating parameters it is recommended that the test gas by setting the switch (7) in the position of GAS.
An important element is the
clean surface welded:
An important element is the
clean surface welded:
TIG welding is very sensitive to surface contamination of the metal. Because of that, before the welding process must be removed from the surface of the
welded lubricants, paints, coatings and oxidized.
When these steps
We start welding.
When these steps
We start welding.
The arc welding device in takes place in a contactless manner (HF) - ignition by means of the ionizer, and closer to the electrode base material at a distance
2-3mm and pressing in the handle or in the manner TIG contact (LIFT) by rubbing the electrodes of the welding.
PARWELD handle PROFESSIONAL HR 17 allows you to increase / decrease the current operating buttons located on the handle, without interrupting the
operator.
After work by the operator follows
ending welding
as a result of the release button on the handle (welding current is gradually reduced and the arc goes out). Until
After work by the operator follows
ending welding
as a result of the release button on the handle (welding current is gradually reduced and the arc goes out). Until
After work by the operator follows
ending welding
as a result of the release button on the handle (welding current is gradually reduced and the arc goes out). Until
the total disappearance of the bow handle can not be removed from the welded surface. Cooling of the weld surface of the cooling gas to prevent oxidation.
After you reboot the welding power supply unit has the operating parameters set last before switching off.
MMA
After selecting switch methods of work (7) MMA, the operator can set three operating parameters: welding current (turning multipurpose knob) and the value HOT
START ARC FORCE.
To do so, press the multifunction knob (1) illuminate the LED ARC FORCE, then hot start. Selection and adjustment of the operating parameters is
carried out similarly while adjusting the parameters in TIG. To obtain high-quality welds
remember to remove impurities
with the work piece. In order
carried out similarly while adjusting the parameters in TIG. To obtain high-quality welds
remember to remove impurities
with the work piece. In order
carried out similarly while adjusting the parameters in TIG. To obtain high-quality welds
remember to remove impurities
with the work piece. In order
to avoid irregularities during operation, should pay attention to the electrodes used were dry.
When these steps
we start welding
When these steps
we start welding
Ignition in the following by a welded by rubbing the electrode surface, and then lifting up the electrode. To avoid weld spatter should be used electrodes
manufacturer's recommendations.
After completion of the welding welder must be left turned on for a short period in order to cool the unit by the fan. After completion of MMA welding
should be removed from weld slag.
VII. TIPS FOR YOU
VII. TIPS FOR YOU
1) The basic types of connections TIG / MMA
1) The basic types of connections TIG / MMA
and butt
b corner
c overlapping
d tee
2) Tungsten electrodes recommended by the manufacturer
2) Tungsten electrodes recommended by the manufacturer
code
the size of the
electrodes
RED
GREEN
GREY
GOLD
108 802
108 812
108 822
108 832
1,6x175 mm
108 803
108 813
108 823
108 833
2,0x175 mm
108 804
108 814
108 824
108 834
2,4x175 mm
108 805
108 815
108 825
108 835
3,2x175 mm
108 806
108 816
108 826
108 836
4,0x175 mm
and 对接 接头
and 对接 接头
b 角 接 接头
b 角 接 接头
c 搭接 接头
c 搭接 接头
d T 形 接头
d T 形 接头
