background image

 

PF50 CE SERIES PORTABLE FILTRATION SYSTEMS 

CHAPTER 1:  INTRODUCTION 

 

 

1-3

 

1.5   Service Personnel 

 

1.5.1   Definitions 

 

A.

 

Qualified and/or Authorized Operating Personnel 

 

1.

 

Qualified/authorized operating personnel are those who have carefully read the information 

in this manual and have familiarized themselves with the equipment functions or have had 

previous experience with the operation of equipment covered in this manual. 

 

B.

 

Qualified Installation Personnel 

 

1.

 

Qualified installation personnel are individuals, or firms, corporations, or companies that, 

either in person or through a representative, are engaged in and are responsible for the 

installation of electrical appliances.  Qualified personnel must be experienced in such work, 

be familiar with all electrical precautions involved, and have complied with all requirements 

of applicable national and local codes. 

 

C.

 

Qualified Service Personnel 

 

1.

 

Qualified service personnel are those who are familiar with Frymaster/Dean equipment and 

have been authorized by Frymaster/Dean to perform service on Frymaster/Dean equipment.  

All authorized service personnel are required to be equipped with a complete set of service 

parts manuals and stock a minimum amount of parts for Frymaster equipment.  A list of 

Frymaster Factory Authorized Servicer’s (FAS’s) is located on the Frymaster website at 

www.frymaster.com

.   

Failure to use qualified service personnel will void the Frymaster 

warranty on your equipment.

 

 

 

1.6  Warranty Statement 

 

 

1.

 

Frymaster L.L.C. warrants the PF50  CE Series  one year, parts and labor, against defects in 

material and workmanship. 

 

2.

 

This warranty is void if equipment is found by Frymaster L.L.C. to have been subjected to 

alteration, misuse, or abuse. 

 

 

 

Summary of Contents for Frymaster MPF50































Reviews: