Weishaupt WEM-KNX Installation And Operating Manual Download

Page: 5 / 36

Installation and Operating Manual

Data protocol converter Gateway WEM-KNX

1 User notes

83320602

▪ 1/202

1-02

▪

Ext. PHauner

5-36

User notes

This manual is necessary for the proper operation of the device and should be stored at

the place of use.

This manual must be read carefully before commissioning, installation and mounting as

well as before changing the configuration setting of the device. The notes in the corre-

sponding sections must be observed.

It is supplemented by the short manual for the WEM-KNX Gateway.

1.1

Target group

This operating manual is intended for operators and qualified specialists. It must be ob-

served by all persons who use the device.

Installing and configuring the device may only be carried out by persons that have the

necessary training or instruction.

It is recommended that you participate in the standardized courses of a KNX-certified

training center before installing, programming and commissioning a KNX system. Here,

the participant acquires the necessary knowledge and skills through practical exercises,

which are also necessary for troubleshooting.

1.2

Symbols

DANGER

Indicates an immediate hazard with high risk. Failure to observe

may result death or serious personal injury if it is not avoided.

WARNING

Indicates an immediate hazard with medium risk. Failure to ob-

serve may result death or serious personal injury if it is not

avoided.

CAUTION

Indicates an immediate hazard with low risk. Failure to observe

may result in light or medium personal injury if it is not avoided.

NOTE

Failure to observe may result in damage to property or environ-

mental damage.

Important information.

▶

Prompts for a direct action.

✔

Result after an action.

■

Enumeration

…

Range

Summary of Contents for WEM-KNX





































Search results

Summary of Contents for WEM-KNX

Reviews:

Related manuals for WEM-KNX

Brands by name

Popular brands

Weishaupt WEM-KNX, Installation And Operating Manual

Search results

Summary of Contents for WEM-KNX

Reviews:

Related manuals for WEM-KNX

Brands by name

Popular brands