Start URL
1.
E
nter the Webserver IP Address of
the target device t
o be connected.
2.
Enter the Path or URL of the HTML
file name right after the “/” slash.
3.
When resetting HMI or communication
failure happens, the seconds in which HMI
attempts the connection again can be set.
Info
Display HMI information, including
MicroBrowser version and firmware version.
Click ”Software Update” to update
MicroBrowser Version.
1.
Insert a SD card into HMI, click
”Software Update” to start updating.
2.
Or, after inserting SD card, switch ON
DIP SW3 and then reboot HMI.
DIP SW Settings
Power
The HMI can be powered by DC power only, voltage range: 24±20% Volts DC, compatible with
most controller DC systems. The power conditioning circuitry inside the unit is accomplished by
a switching power supply. The peak starting current can be as high as 2A.
Fusing
Require-
ments
If the display does not come on within 5 seconds of power up, remove power. An internal fuse
will prevent damage if the polarity of the DC power is incorrect. Check wiring for proper
connections and try to power up again.
High
Voltage
An Internal fuse will prevent damage for over voltage condition however it isn
’t guaranteed. DC
voltage sources should provide proper isolation from main AC power and similar hazards.
Emergency
Stop
A Hard-wired EMERGENCY STOP should be fitted in any system using HMI to comply with ICS
Safety Recommendations.
Supply
Voltage
Condition
Do not power the HMI and inductive DC loads, or input circuitry to the controller, with the same
power supply. Note: The 24 VDC output from some controllers may not have enough current to
power the HMI.
Wire
Routing
a. Wire lengths should be minimized (Max: 500m shielded, 300m unshielded).
b. Wires should be run in pairs with a neutral or common paired with a hot or signal line.
c. If wiring is to be exposed to lightning or surges, use appropriate surge suppression devices.
d. Keep AC, high energy, and rapidly switching DC wiring separate from signal wires.
e. Equip ungrounded DC supplies with a resistor and capacitor in parallel to earth ground.
This provides a path for static and high frequency dissipation. Typical values to use are 1MOhm
and 4700pF.
Hardware
Considerations
The system designer should be aware that devices in Controller systems could fail and thereby
create an unsafe condition. Furthermore, electrical interference in an operator interface can lead
to equipment start-up, which could result in property damage and/or physical injury to the
operator.
If you use any programmable control systems that require an operator, be aware that this
potential safety hazard exists and take appropriate precautions. Although the specific design
steps depend on your particular application, the following precautions generally apply to
installation of solid-state programmable control devices, and conform to the guidelines for
installation of Controllers recommended in NEMA ICS 3-304 Control Standards.
Programming
Considerations
To conform with ICS Safety Recommendations, checks should be placed in the controller to
ensure that all writable registers that control critical parts of plant or machinery have limit
checks built into the program, with an out-of-limit safe shut down procedure to ensure safety of
personnel.
GME60IWP0_MT605_607_610iWPV1WK_Installaiton_120525
6
DANGER
CAUTION
NN
Limited Warranty
This product is limited warranted against defects in design and manufacture. The proven
defective pro
duct will either be repaired or replaced, at Weintek’s discretion. This warranty
shall not cover any product which is
(a) Out of warranty period which is 1 year from the date of purchase.
(b) Damage caused by Force Majeure, accident, negligence, improper installation or misuse.
(c) Product has been repaired or taken apart by unauthorized technicians.
(d) Products whose identification markings have been removed or damaged.
NOTE:
Make sure that all local and national electrical standards are met when installing
the unit. Contact your local authorities to determine which codes apply.
7
CAUTION
NOTE:
Make sure that all local and national electrical standards are met when
installing the unit. Contact your local authorities to determine which codes apply.
8
SW1
SW2
SW3
SW4
Mode
ON
OFF
OFF
OFF
Touch Screen Calibration Mode
OFF
ON
OFF
OFF
Hide HMI System Setting Bar
OFF
OFF
ON
OFF
Boot Loader Mode
OFF
OFF
OFF
ON
MT607iWP/MT610iWP
Normal
MT605iWP
Must stay OFF
OFF
OFF
OFF
OFF
MT605iWP
Normal
MT607iWP/MT610iWP
Must stay OFF
NOTE:
Since MT605iWP (4.3
”) does not support
SD card, to update MicroBrowser version,
please contact your distributor.