2 | EN
Awning mode
(1 x flash of the Transmit LED)
The awning is automatically retracted when the current measured
light value changes from 1 to 0 (late evening) or when the current
measured light value changes from 0 to 1 (early morning).
Sight protection mode
(2 x flash of the Transmit LED)
To keep the blind closed in the evening too, close the blind manual-
ly using your hand-held transmitter or a timer.
The current transfers of the light measuring values from 1 to 0
(late in the evening) or from 0 to 1 (early in the morning) are not
considered.
The blind will remain closed throughout the night.
The switching commands such as tilting position (Venetian blind)
or ventilation position (roller shutter) will be executed automatically
the next day.
Setting the mode (awning, privacy, roller shutter)
The BiSens SW-230V can be operated in three different modes.
You can switch through the modes in sequence.
The current mode of the BiSens SW-230V is displayed by means
of the flashing of the green LED.
When the system is supplied it is set by default to the awning
mode.
A different mode can also be preset in OEM versions.
Roller shutter mode
(3 x flash of the Transmit LED)
If the roller shutter is driven manually by a timer or the twilight func-
tion to the lower end position, the light function (driving according
to set light value) will be switched off.
The current transitions of the measured light values from 1 to 0
(late in the evening) or from 0 to 1 (early in the morning) will be
ignored.
You can switch on the light function again in several different ways:
– a manual
UP
travel command (button on the
BiSens SW-230V) moves the blind to the upper end position.
– an automatic timer command moves the blind to the upper end
position.
– Set the sliding switch of your transmitter briefly to MANUAL
mode and then to AUTO mode.
Changing the mode
You will find the multi-way switch for setting the wind threshold value
on the underside of the BiSens SW-230V.
1. Use a small screwdriver to set the multi-way switch to
Function
.
2. Press and hold the
UP
and
DOWN
buttons for at least 3 seconds.
Pressing the two buttons again switches to the next mode.
The current mode of the BiSens SW-230V is displayed by means
of the flashing of the transmission LED.
The operating mode is indicated by the flashing signal.
Transmit LED flashes 1x
→
awning mode
Transmit LED flashes 2x
→
privacy mode
Transmit LED flashes 3x
→
shutter mode
The mode set is indicated at each radio transmission by the flashing
of the Transmit LED (LED flashing pattern 1x per minute).
Set the multi-way switch back from
Function
to a wind value of your
choice.
Teach in BiSens SW-230V
Condition:
The end positions of the awning are set, a
transmitter is programmed.
1. Move the blind to the centre position.
2. Press and hold the
UP
,
DOWN
and
P
buttons on the programmed
hand-held transmitter for at least 3 seconds.
If the awning now travels UP and DOWN, continue at 4.
If the awning does not travel UP and DOWN, continue at 3.
3. Push the
STOP-/P-
button at the BiSens SW-230V for 3 seconds
until the transmission LED flashes quickly orange. The blind now
moves UP and DOWN for 2 minutes. The Transmit LED will flash
orange rapidly every time a button is pressed if the system is in
learning mode.
4. Press the UP button on the unit immediately after an up move-
ment (retract movement) begins. The drive will stop briefly.
5. Press the DOWN button on the unit immediately after a
move-
ment begins
. The drive will stop.
The BiSens SW-230 V is now programmed.
Symbols on the unit
Wind settings
DOWN
button
UP
button
STOP/P
button
/P
Light settings
