Weil-McLain CGt 2 Series Manual Download Page 53

Page: 53 / 68

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Troubleshooting — control module lights

(cont.)

12c

CHART 5 –– PRESS SWITCH

light flashing and POWER light on steady

–– Usually indicates pressure switch opened during run cycle ––

–– May also be caused by wind gusts in excess of 40 mph for non-direct vent sidewall-vented boilers ––

Electrical shock hazard

— Wherever you see ▲

TURN OFF POWER

▲, follow the instructions. Failure to follow

instructions could result in severe personal injury, death or substantial property damage.

• Reset boiler control by turning off power at service switch or turning down thermostat for at least 45 seconds.
• Thermostat should call for heat and appropriate zone valves open.

Does inducer motor operate?

Yes

• Inspect and check wire

harness from control

module to pressure switch.

• Reseat connector in control

module receptacle.

• If harness is intact and

properly seated, but

problem persists, replace

control module.

• Retest.

• Check air pressure switch per manual Section 12b,

page 46.

• Replace if necessary. Retest.

• Clear vent and recycle boiler.
• Recheck boiler operation.

• Replace inducer

assembly.

• Retest.

• Boiler should be in

normal operating

sequence.

• Observe operation until

thermostat is satisfied

and inducer has

completed its post-

purge cycle.

• Remove

INDUCER

plug (Figure 33

, Item 6

, page 48)

from plug receptacle of control module.

• Place voltmeter leads across the

120VAC N

and

120VAC H

pins of the

INDUCER

receptacle (left col-

umn center and right column bottom pins).

Does the voltmeter indicate

120VAC

Yes

• Remove one of the wires connected to the pressure

switch.

• Check continuity across the switch terminals.

Does the ohmmeter indicate the switch is closed?

Yes

• Wait 5 minutes.

PRESS SWITCH

light flashing?

Yes

Is vent blocked?

Yes

Summary of Contents for CGt 2 Series





































































Search results

Summary of Contents for CGt 2 Series

Reviews:

Related manuals for CGt 2 Series

Brands by name

Popular brands

Weil-McLain CGt 2 Series, Manual

Search results

Summary of Contents for CGt 2 Series

Reviews:

Related manuals for CGt 2 Series

Brands by name

Popular brands