background image

9

11. Note: The WEIDER PRO 545 is designed to be

used with both olympic and standard barbells. If you
will be using an olympic barbell, assemble the base
in the wide position, as shown in the main drawing.
If you will be using a standard barbell, assemble the
base in the narrow position, as shown in the inset
drawing.

Attach each section of the Base (20, 55) to an
Adjustment “U” Bracket (31) with two M8 x 68mm
Bolts (8) and two M8 Nylon Locknuts (12).

Do not

tighten the Nylon Locknuts yet.

12. Slide a Rear Upright (19) onto the indicated M8 x

58mm Carriage Bolts (6) in either section of the
Base (20, 55).

The Rear Upright must be oriented

as shown, with the indicated holes facing for-
ward. A second person must hold the Upright at
the location shown during the step.

Partially

tighten an M8 Nylon Locknut (12) onto each
Carriage Bolt 

but do not fully tighten the Nylon

Locknut. Note: The heads of the Carriage Bolts
must lock into the square holes in each section
of the Base in order to tighten the Nylon
Locknuts; you may need to slide your fingers
under the Base to hold the Carriage Bolts in
place while you partially tighten the Nylon
Locknuts.

Assemble the other Rear Upright (19) in the same
manner.

13. Press 1” Round Inner Caps (41) into the ends of the

Weight Rests (37).

13

11

12

8

8

20

12

12

55

31

6

6

12

19

19

These holes

must face

forward

41

41

37

12

8

8

55

20

55

20

31

A second person must hold

each Upright here while the

Nylon Locknuts are attached

Summary of Contents for 831.150471

























Reviews: