WEIDER CLUB 190 T User Manual Download Page 3

3

WARNING:

To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your weight bench before using your weight bench.

ICON assumes no responsibility for personal injury or property damage sustained by or through the

use of this product.

1. Before beginning any exercise program, con-

sult your physician. This is especially impor-

tant for persons over age 35 or persons with

pre-existing health problems.

2. Use the weight bench only as described in

this manual.

3. It is the responsibility of the owner to ensure

that all users of the weight bench are ade-

quately informed of all precautions.

4. The weight bench is intended for home use

only. Do not use the weight bench in any

commercial, rental, or institutional setting.

5. Keep the weight bench indoors, away from

moisture and dust. Do not put the weight

bench in a garage or covered patio, or near

water.

6. Place the weight bench on a level surface,

with enough clearance around the weight

bench to mount, dismount, and use the

weight bench.

7. Inspect and properly tighten all parts regular-

ly. Replace any worn parts immediately.

8. Keep children under age 12 and pets away

from the weight bench at all times.

9. Keep hands and feet away from moving

parts.

10. Always wear athletic shoes for foot protec-

tion while using the weight bench.

11. The weight bench is designed to support a

maximum user weight of 300 lbs. (136 kg),

and a maximum total weight of 410 lbs. (186

kg). Do not place more than 110 lbs. (50 kg),

including a barbell and weights, on the

weight rests. Do not place more than 50 lbs.

(23 kg) on the leg lever.

12. Do not use a barbell that is longer than 5 ft.

(1.5 m) with the weight bench.

13. Always place the same amount of weight on

both ends of the barbell. While adding or

removing weights, always keep some weight

on both ends of the barbell to prevent the

barbell from tipping. Always secure weights

with the spring clips.

14. Before using the leg lever, place the barbell

with the same amount of weight on the

weight rests to balance the bench.

15. Before using the backrest in an inclined

position or a level position, make sure that

the backrest support is inserted fully into the

uprights and that it is turned to the locked

position.

16. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

IMPORTANT PRECAUTIONS

Summary of Contents for 190 T

















Reviews: