background image

Operation and Maintenance Manual and User Service Guide for Industrial Power WP10 Series Diesel Engine 

51

 

Weichai  industrial  power 

engine  spare  parts  “Th

ree-

guaranty” 

warranty specification  

Weichai  power promise  of 

quality warranty and “Three

-

guaranty”

  for  spare 

parts: Under the normal use and maintenance, Weichai Power will free repair 
or  maintain  the  damaged  parts  caused  by  its  quality  within  the 

“Three

-

guaranty” period.

 

1 Spare part 

“Three Guaranty” specifications

 

The failed parts have quality defect, the 

“Three Guaranty”

 period will 

calculated according to the date on the sale invoice or sale list printed by 
Weichai Spare Part System.  

1.1 Low-value we

ar parts are not covered by “Three guaranty”:

 

Gaskets: all except for cylinder head gaskets;  

Filter elements: air cleaner, fuel filter, oil filter; 

Rubber: waterproof ring of cylinder liner, sealing rubber ring, sealing gasket 
of oil sump;  

Sensor: coolant temperature sensor, oil pressure sensor;  

Mate parts: matching parts of nozzle, injection pump plunger and barrel;  

Fasteners: clamp and clip; 

Bolts purchased separately: connecting rod, cylinder head, main bearing etc.  

1.2 For wear parts and electrical parts, the warranty period is 3months  

The following parts belong to wear parts or electrical parts  

Starter 

Belt 

Preheating 
device 

Generator 

Electronic throttle pedal 

A/C compressor 

Fuel/water separator 
(without element ) 

Engine harness 

Fuel-saving 
switch 

10 

Thermostat 

11 

Clamp 

12 

Monitor 
assembly 

13 

Solenoid valve 

14 

Power pre-supply pump 

15 

Relay 

16 

Battery 

17 

Piston ring 

18 

Piston 

19 

Cylinder liner 

 

 

 

 

Summary of Contents for WP10






















































Reviews: