background image

Page 20

Shutdown/Replacement Parts/Warranty

SG Manual

I. CARE OF THE BURNER DURING EXTENDED SHUTDOWN

Heating  equipment  is  oftentimes  located  in  an  environ-

ment  conducive  to  corrosion  and  general  deterioration  if 

not properly protected and periodically checked, especially 

during  an  extended  period  of  shut  down.    The  following 

procedures should be followed if the burner is going to be 

placed out of service even for a short period of time.

1.

  Turn the main manual fuel valve OFF.

   

J. REPLACEMENT PARTS

2.

  Turn off the main electrical disconnect to the burner 

OFF.  Follow tagout / lockout procedures.

3.

  Place a notification tag or label at the main manual 

fuel valve giving reason for shutdown.  Follow tagout / 

lockout procedures.

4.

    If  the  burner  is  in  an  area  subject  to  sweating  and 

condensation, cover the control cabinet and electrical de-

vises with plastic and secure with twine or tape.

5.

  Should the burner be out of service for more than thirty 

(30) days, a complete operational safety check must be 

made at the time of restart.  The restart must be treated 

as a new burner start-up (see burner start-up section in 

this manual).

K. WARRANTY VALIDATION & FIELD START-UP REPORT

As a final step, forward the top copy of the Warranty 

Validation and Field Startup Report, Form 113, to: 

WEBSTER COMBUSTION TECHNOLOGY, LLC 
619 Industrial Road, Winfield, KS 67156.

WEBSTER Series SG Burners are listed by 

Underwriters Laboratories, Inc. (U.L.). Also by 

the State of Massachusetts Fire Marshall, City 

of New York Board of Standards and Appeals, 

State of Minnesota, and can be packaged to 

meet specific requirements of CSD-1, GE GAP, 

IRI, FM, NFPA, MIL or other special insurance or 

local code requirements.

The following replacement parts should be stocked to 

support uninterrupted burner operation.
Electrode

Blower Wheel

Ignition Transformer

Flame Scanner
Items with greater life expectancy and/or greater dollar 

value, such as flame safety controls, main gas valves 

and blower motors shopuld be obtained from your local 

Webster representative when a need arises.

An illustrated parts drawing is included within the Burner 

Instructions Manual to aid in parts identification. The name 

of the part needed should be established from the draw-

ing, then the part number can be obtained from the burner 

material list contained in the Burner Instructions and 

service Manual.

NOTE 

Always give Webster Combustion Serial 

Number and/or UL Serial Number when 

ordering parts.

CAUTION

ALWAYS KEEP THE MAIN FUEL VALVE(S) OFF IF THE BURNER 

IS SHUT DOWN FOR AN EXTENDED PERIOD OF TIME.

Summary of Contents for Cyclonetic SG Series

























Reviews: