manualshive.com logo in svg

Weber Summit E 470, Owner'S Manual, Page: 10 / 36

Share
Download
Weber Summit E 470 Owner'S Manual Download Page 10

10

GAS INSTRUCTIONS

LEAK-CHECK PREPARATION 

m

  WARNING: The gas connections of your SUMMIT gas grill have 

been factory-tested. We do, however, recommend that you leak-
check all gas connections before operating your SUMMIT gas 
grill.

Remove Control Panel

Tools needed: Screwdriver, pliers, and towels.
A)  Remove burner control knobs 

(1).

B)  Open both doors. With a screwdriver, remove screws from the underside of control 

panel 

(2).

C)  Lift and remove battery housing located inside grill cabinet 

(3). 

D)  Using needle-nose pliers, disconnect wire terminals from the top of battery housing 

(4). Do not pull on the wires; remove them by pulling on the wire terminals.

E)  Place towels on the tops of both door assemblies. 

This will protect control panel and 

door assemblies from getting scratched on next step. 

F)  Tilt bottom of control panel forward. Lift slightly 

(5) and then rotate it face down to 

rest on tops of door assemblies. (Be careful not to break or disconnect wires for the 
control panel LEDs.)

G)  Carefully pull battery wires out from the inside of the grill cabinet 

(6). 

H)  Fully open right door. Place control panel on floor, leaning against towel covering right 

door assembly 

(7).

2

3

4

6

7

1

5

Summary of Contents for Summit E 470





































Reviews:

No comments