background image

  WWW.WEbER.cOm

®

27

mAINTENANcE

11

10

9

16

17

18

12

13

14

15

20

19

Burner Tube Removal

To remove burner tube(s):
A)  Remove igniter wire(s) from igniter clip(s) 

(9) .

B)  Remove screw that holds burner tube to the cookbox using a 5/16" nut-driver 

(10) .

C)  Pull burner tube assembly (this includes igniter) up and out of cookbox 

(11) .

 

Note: 310 units will have an additional earthing wire attached to the centre burner 
tube

 

(12) .

Burner Tube Cleaning

To clean the burner tube(s):
A)  Look inside each burner with a torch 

(13) .

B)  Clean the inside of the burners with a wire 

(14) (a straightened-out coat hanger will 

work) . 

C)  Check and clean the air shutter opening at the ends of the burners . Check and 

clean the valve orifices at the base of the valves . Use a steel bristle brush to clean 
outside of burners 

(15) . This is to make sure all the burner ports are fully open .

m

  CAUTION: Do not enlarge the burner ports when cleaning.

Burner Tube Reinstallation

To reinstall burner tubes:
A)  Slide burner tube and igniter wire through hole in cookbox 

(16) . Refer to 

“ELECTRONIC IGNITION SYSTEMS OPERATIONS” for proper burner position .

B)  Align burner tube with valve .

m

  CAUTION: The burner openings (17) must be positioned 

properly over the valve orifices (18).

C)  Re-install screw that holds the burner tube to the cookbox using a flathead 

screwdriver . Burner tube may seem loose 

(19), when screw is snug . This is normal .

D)  Route wires back through igniter clips . Refer back to figure 

(9) .

m

  CAUTION: All wires must be properly routed through wire 

clips.

E)  Attach wires to module, following the numerical/colour coding 

(20) . Refer to 

“ELECTRONIC IGNITION SYSTEM OPERATIONS” for proper attachment of wires .

m

  WARNING: Make sure that all parts are assembled and 

hardware is fully tightened before operating the grill. Your 
actions, if you fail to follow this Product Warning, may 
cause a fire, an explosion, or structural failure resulting 
in serious personal injury or death as well as damage to 
property. 

Summary of Contents for 54412

































Reviews: