Weathermatic SmartWire 9600TW Owner'S Manual Download

Page: 36 / 48

http://support.weathermatic.com

12.0 Troubleshooting Guide

PROBLEM

CAUSES

SOLUTIONS

SmartLine®

controller does not

turn on zone when

expected

Sensor jumper is removed and no

sensor is connected (Sensor LED is

red)

Install jumper wire between SEN terminals

Select OFF mode if desired

Sensor wires have been cut (Sensor

LED is red)

Repair wires

Zone comes on at unexpected time

Program daily start times not set properly or multiple start times set.

Check Program Start Times

Stacked program has commenced

normal operation

Modify settings (such as program start times, zone run times) to prevent

stacking if undesirable

Time of day or date not set properly

Review/set time of day and date

Watering days or omit days/dates not

set properly

Review/set watering days or omit days/dates

Run/Soak feature has extended

watering window

Normal operation to allow water infiltration and prevent runoff

Controller does not operate zone for

expected run time

Pause for Run/Soak in progress. This is normal operation to allow water

infiltration and prevent runoff

Check seasonal % settings if BASIC mode is in use.

Module not installed

Install module

No initial AC power-up of controller

Connect AC power and close control panel

Summary of Contents for SmartWire 9600TW

















































Search results

Summary of Contents for SmartWire 9600TW

Reviews:

Related manuals for SmartWire 9600TW

Brands by name

Popular brands

Weathermatic SmartWire 9600TW, Owner'S Manual

Search results

Summary of Contents for SmartWire 9600TW

Reviews:

Related manuals for SmartWire 9600TW

Brands by name

Popular brands