Weathermatic SmartWire 9600TW, Owner'S Manual

Page: 18 / 48

12
http://support.weathermatic.com
7.0 Programming the SL9600TW Controller
For most watering programs set only Start Time #1. The #1
Time will water all zones with Zone Run Times set in that
program in consecutive order. Extra start times will re-run
all zones. Extra start times may be used for new planting
grow-in or other special local conditions. Unused start times
must be set in the OFF position. To set a start time at OFF,
press on either UP or DOWN button until you reach the OFF
position located between 11:50 PM and Midnight.
When setting program start times, check the program icon
in the display to see whether you are working in A, B, C or D.
Use PGM button to move between programs. Use NEXT and
BACK buttons to move between start times. Use UP and DOWN
buttons to set each start time desired. Start times are selectable
in 10-minute increments.
Push PGM button to assign zone time in one or more programs.
Care has to be taken when programming. You need to have
awareness of the hydraulic capacity of the irrigation system
piping and points of connection so that they are not exceeded.
Further care should be taken so the electrical capacity of the
controller is not exceeded. The electrical capacity is 750 mA
or 3 irrigation solenoids. A pump start relay may require more
mA than a solenoid. Keep aware of these boundaries when
scheduling stations to initiate and operate simultaneously.
Note: Be sure you select the AM/PM time as desired by
scrolling past 12. (For international users, the display will show
international hours instead of AM/PM.)
7.4 Zone Run Times
Your SmartLine® controller will display
remaining hours, minutes and seconds
when a zone is watering. However, in
this position you are only required to
set minutes (or hours and minutes)
for each zone as desired for operation
time. Seconds are not selectable.
Use NEXT and BACK buttons to select zone for run time
setting. All zones are selectable from 1 minute to 9 hours and 55
minutes. Run times of OFF to 59 minutes are selectable in one
minute increments. Run times of 1 hour to 9 hours 55 minutes
are selectable in 5-minute increments. Use UP or DOWN buttons
to set flashing time values for each zone. If a zone is not to be
used, set it to OFF.
Caution: If an unused zone is turned on and activates a pump
start relay, the pump may overheat or cause a pipe to burst. To
prevent operating a pump with no flow (dead heading), make
sure all unused zones are set to OFF.
7.5 Days to Water
In this dial position you can select
a DAYS, INTERVAL, or ODD/EVEN
schedule. Use UP and DOWN buttons
to select which type of schedule you
want in your SmartLine® controller.
Remember to check the Program
(PGM) selection showing in the display. You can select a
different watering schedule for each program if you wish.
If you select DAYS, then use the NEXT button to step through
each day of the week and the UP and DOWN buttons to select
SMART
BASIC
MORE / LESS
SOIL TYPE
PLANT TYPE
SPRINKLER TYPE
ZIP CODE / LATITUDE
OMIT TIMES / DAYS
SEASONAL % ADJUST
MANUAL ZONE
MANUAL TEST
ADVANCED
MENU
RUN
SYSTEM OFF
CURRENT TIME / DATE
PROGRAM START TIMES
ZONE RUN TIMES
SMART
BASIC
MORE / LESS
SOIL TYPE
PLANT TYPE
SPRINKLER TYPE
ZIP CODE / LATITUDE
OMIT TIMES / DAYS
SEASONAL % ADJUST
MANUAL ZONE
MANUAL TEST
ADVANCED
MENU
RUN
SYSTEM OFF
CURRENT TIME / DATE
PROGRAM START TIMES
ZONE RUN TIMES
DAYS TO WATER
SMART
BASIC
MORE / LESS
SOIL TYPE
PLANT TYPE
SPRINKLER TYPE
ZIP CODE / LATITUDE
DAYS TO WATER
OMIT TIMES / DAYS
SEASONAL % ADJUST
MANUAL ZONE
MANUAL TEST
ADVANCED
MENU
RUN
SYSTEM OFF
CURRENT TIME / DATE
PROGRAM START TIMES
SMART
BASIC
MORE / LESS
SOIL TYPE
PLANT TYPE
SPRINKLER TYPE
ZIP CODE / LATITUDE
DAYS TO WATER
OMIT TIMES / DAYS
SEASONAL % ADJUST
MANUAL ZONE
MANUAL TEST
ADVANCED
MENU
RUN
SYSTEM OFF
CURRENT TIME / DATE
PROGRAM START TIMES
ZONE RUN TIMES